Will Curt Trailer Hitch 13055 Fit 2012 Ford E-250 With Spare Tire

Question

Question:

I dont see in the specs for hitch receiver Item # 13055 if it works with spare tire mounted under frame? Can you please confirm? I have a Ford 2012 E-250 van.

asked by: Tom

0

Expert Reply:

The Curt hitch will fit your 2012 Ford E-250 with a spare tire; the correct hitch is the following part:

- Curt Trailer Hitch Receiver # 13055

expert reply by: Kyle S

0

Answer 1

We have trailer hitches to fit both Ford E-250s and Ford F-250s however the hitches are different and not interchangeable. You didn't say which vehicle you need a hitch for. If you need one for an E-250 van then I recommend part #75703. Or if you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Will Curt Trailer Hitch 13055 Fit 2012 Ford E-250 With Spare Tire

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching