Replacement Optronics Rectangular Trailer Tail Light with Three Prong Plug

Question

Question:

a guy bumped my trailer broke my light when i took the housing apart i noticed that it comes with and easy to change 3 prong plug where can i purchase a new one optronics is on the plastic

asked by: Ron P

0

Expert Reply:

The ONE LED Trailer Tail Light part # STL0067RPG for driver or part # STL0066RBG for passenger has a three prong pigtail attached to the light so this may be what you're looking for. The ONE LED Trailer Tail Light measures 7-3/4" long x 3-1/8" tall x 2-7/8" deep and severs six functions; stop, tail, turn, reflector, side marker, and plate light.

expert reply by: Conner L

0

Answer 1

I looked up pictures of your 2015 Tracker Grizzly 1754 SC and it appears to have the trailer taillights part #ST36RB for the right hand side and the part #ST37RB for the left hand side.

view full answer...

Answer 2

From what we've found online, the proper replacement for your S2T216AP2 is #STL16RB for the passenger side and #STL17RB for the driver side.

view full answer...

Answer 3

The tail lights you have on your trailer are the ONE LED Trailer Tail Lights part #STL0067RPG for the driver side and part #STL0066RBG for the passenger side. Unfortunately, Optronics does not offer a replacement lens for this particular light so…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Replacement Optronics Rectangular Trailer Tail Light with Three Prong Plug

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching