Installing TRU77FR Spindle

Question

Question:

What does it take to prepare axle for new spindle? TRU77r.

asked by: Stephen D

0

Expert Reply:

The # TRU77FR spindle accepts a 3 inch axle beam, and the spindle is designed to be welded into place. If the axle tube is painted on the ends, you'll want to take the tubing down to bare metal so you get the proper penetration on your weld.

expert reply by: Mike L

0

ID of Mounting End of TRU77FR Spindle
(click to enlarge)

Answer 1

In order to find the correct replacement parts for your 2000 Eagle boat trailer you will need to identify your axle. We have no way of looking up specific parts for your trailer. A good place to start would be with the axle tag. This should have the…

view full answer...

Answer 2

We do carry the #84 spindle #TRU77FR which is designed to accept a 3" axle beam. The spindle itself has an overall length of 6-1/8". This is the only #84 spindle we have for a 3" tube. All of the others would be a #42 spindle like the…

view full answer...

Answer 3

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 4

It depends on how many axles you have. If you have two axles then yes it would be overloaded because that would be 7,000 pounds. If you have three axles you would be fine. Depending on what your bolt pattern is I would go up in axle capacity and put…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Installing TRU77FR Spindle

Product Page this Question was Asked From

Continue Researching