Replacement Trailer Brake Assemblies with Axletek-10-GG On Assemblies
Updated 10/24/2024 | Published 09/29/2019
Question:
Hi, will these be a direct replacement for my current trailer brakes that are stamped Axletek-10-GG?
asked by: Ernesto R
0
Expert Reply:
Yes, the Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the same brand and number on a sticker on the inside of the assembly.
I also attached an install video for these for you to check out as well.
expert reply by:
Jameson C
0
click to enlarge
Product Page this Question was Asked From
etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 13 Inch Wheel
- 14 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Search Results: axletek 10 gg
- Search Results: bd2~545
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Search Results: trailer brakes
- Search Results: libra
- Search Results: equalizer
- Search Results: shake
- Search Results: shackle
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 5-1/2 - Pre-Greased
- Video: Review of etrailer Trailer Brakes - Electric Drum Brake Kit - AKEBRK-35-SA
- Shop: RV Camera
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Q&A: Solution to Replace WFCO 8735P to Charge Lithium Batteries
- Shop: Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System
- Shop: Trailer Hitch
- Shop: Gooseneck Hitch
- Q&A: Replacement Hub for AxleTek Hub # BD2-545-17
- Video: Let’s Check Out the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles
- Video: Feature Review Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles
- Video: Review of the Trailer Hub and Drum Assembly
- Shop: Blind Spot Detection
- Q&A: Torque Spec for Tightening Trailer Brake Assemblies to Trailer Spindle
- Q&A: Correct Replacement for Tru-Ryde Hub/Drum RVD-H-545
- Q&A: Replacement Hub/Drum and Brake Assemblies For a Tru Ryde Drum RVD-U-54XX on Boat Trailer
- Q&A: Lithium Compatible Replacement for WFCO WF-8735 RV Power Converter
- Q&A: Replace WF-8735P Power Center with Lithium Ready Model
- Video: etrailer Easy Grease Trailer Hub and Drums Installation - 2020 K-Z Sportsmen Classic Travel Trailer
Louie
10/24/2024
I have a 2022 Grand Design Imagine XLS 21BHE. Today I found that the brake backing plate was spec out for a 3,500 axle but the GD Imagine XLS 21BHE RV that I have has dual 3,000 lbs rated axles. The issue with having this configuation is that hub/spindle hole in the backing plate is much larger then the spindle of a 3,000 lbs rated axle. Leaving opening (slots) next to the bolts that hold the backing plate to the hub/spindle. The major issue with this is that water is getting inside the brake shoe area. No brakes, just a lot of water and rust where the brake shoes are. Just wondering if anyone has run into that with their GD Imagine? Louie