Which Shank Comes With The Curt TruTrack Weight Distribution System C17501?

Question

Question:

What shank comes with the curt 17501?

asked by: Michael

0

Expert Reply:

I confirmed with Curt that the correct replacement shank for Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 15,000 lbs GTW, 1,500 lbs TW # C17501 is the Curt Adjustable Weight Distribution Shank - 8" # C17100. I attached a short demonstration video for you to check out.

expert reply by: Andrew N

0

Answer 1

Hey Mike! I went out to the warehouse to check, and there actually is only 1/8" from the center of the topmost adjustment hole to the top of the shank for the Curt Adjustable Weight Distribution Shank #C17100. Check out the attached photo to…

view full answer...

Answer 2

Weight distribution shanks are one of the few parts that are okay to swap between brands and still work; since both shanks fit in a 2" hitch receiver you can use the Curt Adjustable Weight Distribution Shank #C17100. We do carry the Equal-i-zer…

view full answer...

Answer 3

It sounds like you're looking for a new weight distribution shank with less drop and if that's the case we have tons of great options. In order to see how much drop/rise you need you can measure from the ground to the top inside edge of the…

view full answer...

Answer 4

For your weight distribution system, the rise is due to the shank itself. Most weight distribution shanks are able to be interchanged between manufacturers. For your application, I recommend the Curt Adjustable Weight Distribution Shank - 8"…

view full answer...

Answer 5

I believe we have just what you're looking for. Check out the Curt Adjustable Weight Distribution Shank #C17100. This weight distribution shank has 7 holes for adjustment, will work with 2" trailer hitches, and has a maximum weight capacity…

view full answer...

Answer 6

Yes the Curt weight distribution shank part #C17100 is perfectly compatible with the Fastway e2 weight distribution system you have.

view full answer...

Answer 7

I spoke with my contact at Curt and the Bolt-Together Adjustable Weight Distribution Shank - 12 Inch, #C17100, does take 3/4 inch diameter mounting bolts. The measurement between the bolt holes from center to center is 1-1/4 inches. I have attached a…

view full answer...

Answer 8

The Reese Weight Distribution System w Shank - Round Bar - 6,000 lbs GTW, 600 lbs TW #RE34FR is 49911 you referenced. It definitely doesn't sound right that there is more than 4 inches of difference from the base of the hitch ball when inverting…

view full answer...

Answer 9

Yes, we do offer a replacement shank for the Curt Weight Distribution Hitch item #C17500. It is the Curt Adjustable Weight Distribution Shank - 8" item #C17100.

view full answer...

Answer 10

The Curt Adjustable Weight Distribution Shank #C17100 will work with the #EQ37101ET which is the 90001000 system you referenced. That system is recommended for total tongue weights between 600 and 1000 lbs. That total tongue weight includes the…

view full answer...

Answer 11

Hey Randy, welcome back and congrats on the new truck. For a 450 lbs - 500 lbs tongue weight, I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ90-00-0600. This system will let you back up with it installed and…

view full answer...

Answer 12

Hey Cory, thanks for reaching out. The correct weight distribution (WD) hitch depends on your loaded tongue weight. The 340 lb hitch weight is the dry hitch weight which does not include batteries or fuel. So your actual loaded hitch weight will…

view full answer...

Which Shank Comes With The Curt TruTrack Weight Distribution System C17501?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching