See what our Experts say about this Fastway Accessories and Parts

• Fastway e2 Weight Distribution for 2025 Ford F-150 Towing Enclosed Trailer
  Hello again Frank; tongue weight is typically 10-15% of your trailer weight. At 5,400 lbs you could go over the max 800 lb tongue weight of the # FA94-00-0800 but that probably isn't the case here. If you really want to be sure you could always pick up a small scale like the # BTBRV004 or # BTBRV99FR. Assuming you're in that 400-800 lb range this will remove that little bit of sag (sounds like it isn't a concern but it still helps) and cut down on your trailer sway. Regarding the shank,...
  view full answer...
• Recommended Weight Distribution Shank for a 2024 Toyota Tundra Limited
  Hey Steve! Thanks for the kind words and welcome back! You're going to be good using your existing Equalizer 4-point sway control weight distributing hitch with your new Tundra. You may need a taller shank like the item # FA92-02-4213 due to the difference in hitch height is all can I think of. If you're happy with your current system my recommendation is to keep using it.
  view full answer...
• Recommend Weight Distribution Hitch For My 2019 Chevrolet Silverado 2500
  When it comes to installing a weight distribution on your 2019 Chevrolet Silverado 2500 when towing a 24 foot 10,000 pound car hauler I recommend The Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 12,000 pounds GTW, 1,200 pounds TW # FA92-00-1200. When it comes to using weight distribution you need to be as close as possible to your trailer weight to get the best ride. The Blue Ox Sway Pro # BXW2000 you were looking at would be overkill because it is meant for a trailer...
  view full answer...
• Recommended Weight Distribution Hitch for V-Nose Trailer
  The adjustable height, sway control, and 2-5/16" ball are something you can get on most weight distribution hitches. The main issue for you is the V-nose trailer. This typically limits the installation of a WDH because of the amount of space on the frame. However, with 26" you could use the Fastway system you were looking at. The # FA94-00-1033 is for 600-1,000 lbs of tongue weight so it is a bit much for your setup, instead you will need the # FA94-00-0800. This hitch works for 400-800...
  view full answer...
• Replacement Shank For Fastway e2 Weight Distribution Hitch
  Yes, you can get a replacement shank only for a Fastway e2 weight distribution hitch, and there are different options depending on how much rise or drop you need. - Max 7-3/4" Rise, 3-1/4" Drop: Fastway e2 Weight Distribution Shank # FA92-02-4213 - Max 10-1/4" Rise, 5-1/2" Drop: Fastway e2 Weight Distribution Shank # FA92-02-4214 - Max 12-1/2" Rise, 9-3/4" Drop: Fastway e2 Weight Distribution Shank # FA92-02-4315 As for the bolts to hold the ball and bar mount at an angle, I believe...
  view full answer...
• Is There A 2-1/2" Shank Available For A Fastway e2 Weight Distribution System?
  Hi Robert! The closest one to the Fastway e2 Weight Distribution Shank - 12" Long - 7-3/4" Rise, 5-1/4" Drop - 1.2K TW # FA92-02-4213 you were looking at will be the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 10" Rise/6" Drop # EQ90-02-4900. Equal-i-zer and Fastway are under the same parent company and this will absolutely work with your e2 weight distribution system. It uses the same somewhat standard 1-1/4" hole spacing for the head adjustments (which is used across the whole Fastway...
  view full answer...
• Measurements to Top Hole on Fastway e2 Weight Distribution Shank
  On the Fastway e2 Weight Distribution Shank # FA92-02-4213 the drop position from the top to the center of the first hole is 1-11/16 inches and in the rise position the same measurement is 1-5/8 inches. Error on the picture below it is suppose to say 1-11/16 not 1-1/16. I attached a review video link below.
  view full answer...
  
• Fastway E2 Weight Distribution Hitch Installation Instructions
  The Curt Trailer Hitch Receiver # C15324 is the highest rated compatible hitch for your 2004 GMC Yukon. All other compatible hitches are class 3's whereas this is a class 5. The Fastway e2 Weight Distribution w/ 2-Point Sway Control # FA94-00-1033 does require a torque wrench that is capable of 450 ft-lbs to attach the hitch ball. The hitch ball needs to have a 1-1/4" diameter shank so since you need a 2-5/16" ball you can use the 2-5/16" Hitch Ball # A-6. As for torqueing the hitch...
  view full answer...
• Fastway e2 Shank Recommendation for Towing a Trailer Lower Than Tow Vehicle
  The Fastway e2 Weight Distribution Shank # FA92-02-4213 is a great option, but if you're needing a little more drop then I recommend picking up the Shank # FA92-02-4214 instead because it offers an additional 2" of drop so you can achieve the correct amount of drop for your towing application.
  view full answer...
• Replacement Hitch/Head/Shank for Fastway e2 Weight Distribution System
  Yes, we do offer all of the components for the Fastway e2 Weight Distribution System separately so you can replace just what you need. I assume you need the head, hardware, shank, and hitch ball which is what I will attach below. Head part # FA92-02-1255 Hardware part # FA92-02-9600 Shank part # FA92-02-4213 Hitch Ball part # 19286 or part # A-90
  view full answer...
• Needing Weight Distribution Shank With Greater Drop
  The shank included with the # FA92-00-0600 Fastway weight distribution system you'd looked at will provide up to a 6 inch rise or a 1 inch drop, so it sounds like you're needing a shank that provides more drop. 3-1/4 inches of drop, use # FA92-02-4213. For 5-1/2 inches, use # FA92-02-4214. Or for up to 9-3/4 inches, use # FA92-02-4315.
  view full answer...
• Recommended Weight Distribution Hitch For A 2004 GMC Yukon Denali
  For your 2004 GMC Yukon Denali I actually recommend the Fastway e2 Weight Distribution w/ 2-Point Sway Control Hitch # FA94-00-1033 instead of the Reese, Curt, or Blue Ox hitches. The 2-point sway control provides much better sway control and has no need for lift chains. This also works with a wider range of the hitch weights than the other brands. The no-drill, clamp-on brackets can be adjusted along the trailer frame which will accommodate frame-mounted items such as gas tanks, battery...
  view full answer...
• Will a Different Shank Brand Fit an Equal-I-zer Weight Distribution System
  I actually do not recommend the use of Reese shank # RP54970 with an Equal-I-zer weight distribution system, # EQ37061ET, because the Reese design is such a departure from the Equal-I-Zer design. A shank such as Fastway # FA92-02-4213 or Curt # 17120 are better options and either would work well for you.
  view full answer...
• Measurements to Top Hole on Fastway e2 Weight Distribution Shank
  I'm not sure which you consider to be the top since the Fastway shank, part # FA92-02-4213, can be flipped so I went ahead and took both measurements. Although, there's very little difference. I found that in the drop position from the top to the center of the first hole is 1-11/16 inches and in the rise position the same measurement is 1-5/8 inches.
  view full answer...
  
• Can the Shank on the 10K Fastway e2 Weight Distribution System Be Flipped for More Drop
  The Fastway e2 Weight Distribution System part # FA92-00-1000 comes with a shank that can provide a max of 6" rise or 1" drop. That said, these measurements already reflect the shank being flipped or inverted so no matter which direction the shank was installed you could still only achieve 1" drop. However, I do have an option for you that does not require you to buy two shanks, the Fastway e2 Weight Distribution System part # FA94-00-1033 and the Fastway e2 Weight Distribution Shank part...
  view full answer...
• Weight Distribution Replacement Shank to Keep Hitched Trailer Level to Avoid Sway
  You are correct that a level trailer will be less likely to sway and keeping your hitched trailer level will enable a weight distribution (WD) system to function at its best. It is perfectly okay for a hitch ball to be an inch or so higher than the coupler on the level trailer since a little bit of normal squat will even things out but if your trailer is tipped up at the tongue when it is hitched to your F-150 you'll want to select a different shank for your WD hitch that will allow the...
  view full answer...
• Adding a Second Weight Distribution Head and Shank for a Fastway Weight Distribution System
  Yes, we do have a head only that will work great for you. It is the replacement Fastway e2 head # FA92-02-1255 for 6K to 12K rated systems or # FA92-02-0410 for the 4.5K system. This head is the exact same as the ones that come in the full kits. You would have to use a Fastway head in order to use the Fastway spring bars. Another brand head will not work. You will also need replacement hardware kit # FA92-02-9600 since the above heads do not include this hardware. For a second shank we...
  view full answer...
• Can the Fastway Weight Distribution Shank part # FA92-02-4213 be Used in Rise and Drop
  Yes, the Fastway Weight Distribution Shank part # FA92-02-4213 can be used in the rise or drop position.
  view full answer...
• Can Rock Tamers Mud Flap be Used with Curt Weight Distribution System
  Was the issue with the Rock Tamer # ERT00108 that you didn't have enough space between the hitch opening and the shank for the bracket to fit? Did you return it already? A longer shank would solve that problem like with the Fastway part # FA92-02-4213 which will fit the head of your Curt system part # C17501.
  view full answer...
• Determining Best Weight Distribution System For Travel Trailer Weighing Less Than 6000lbs
  I would be happy to go over how to determine the correct weight distribution system for towing your 1946 Spartan Manon Travel Trailer, but you will need to confirm the total tongue weight of your trailer before deciding an a system. To determine the correct weight distribution system you will need to know the total tongue weight of your trailer which is the tongue weight of your fully loaded and ready to tow trailer plus the weight of any cargo behind the rear axle of your tow vehicle....
  view full answer...
• Availability of Fastway e2 Shank No Longer Than 9-1/2 Inches
  The majority of our WDH shanks have the dimensions listed either in the description or on a diagram. Regardless, 9-1/2" is very short and only one out of everything available comes close. The # AMAC1 has an overall length of 9-15/16". There is nothing shorter than this. The distance from the center of the shank holes to the center of the hitch pin hole is 6-3/4" and it has a drop of 2-5/8" and rise of 7-3/8" when used with trunnion bars. This is compatible with the Fastway e2 # FA92-00-0800.
  view full answer...
• Fastway Weight Distribution for a V-Nose Trailer with Limited Space on Frame
  With a trailer weighing 3,820 pounds the tongue weight will be in the neighborhood of 380 to 573 pounds which is 10 to 15 percent of the gross trailer weight. But to that you also need to add in the weight of anything loaded behind the rear axle of the tow vehicle. So for example if you had 100 pounds of gear behind the tow vehicle rear axle that would make the tongue weight 480 to 673 pounds. The minimum tongue weight for the Fastway system, # FA94-00-1033, to be effective is 400 pounds....
  view full answer...
• Replacement Shank for MaxxTow Adjustable Tri-Ball Mount
  I was able to get confirmation from MaxxTow that there is not an available replacement shank for the MT70197, but because the hole sizes are the same as a standard weight distribution hitch shank you can use something like the Fastway e2 Weight Distribution Shank - 12" Long - 7-3/4" Rise, 5-1/4" Drop - 1,400 lbs TW # FA92-02-4213 in its' place. This would be the best solution available aside from replacing your adjustable ball mount altogether.
  view full answer...
• Will Fastway Weight Distribution Shank Fit a Pro Series Weight Distribution System
  Yes, you can use the Fastway weight distribution shank # FA92-02-4213 with Pro Series RB3 system # PS49581. The shank has 3/4 inch diameter holes spaced 1-1/4 inches apart which is the most common hole size and spacing for weight distribution systems.
  view full answer...

Do you have a question about this Accessories and Part?