Replacement Lift Arm & Operator Mechanism For MaxxAir 4801K

Question

Question:

How can you help us to replace this part? I think its 4801K Maxxair Fan Automatic. We also need the arms replaced as well. Can we order this through you?

asked by: Shirley

0

Expert Reply:

We do have the exact parts you need and yes you can order it through us! I verified with the manufacturer for you that the correct parts for your MaxxAir 4801K are the following:

- Replacement Operator Mechanism # MA10-20281K-1AF

- Replacement Lift Arm for MaxxFan Roof Vents # MA10-20222KS

expert reply by: Kyle S

0

Answer 1

The CC316-01 number you referred to is the original part number of the fan motor. Is it a replacement fan blade or motor you're needing? If that's the case, you'd use the #BVD0218-00-R replacement motor. If you were needing a replacement…

view full answer...

Answer 2

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...

Answer 3

The gearbox inside of the Solera Manual Crank Style Awning Drive Head part #LC300031 is not available separately as a replacement part therefore if you need to replace this you will have choice but to replace the entire assembly.

view full answer...

Answer 4

The 10B21275KE part #MA39FR replaces the 10-21275KE you mentioned as well so if you had an older model number you could use it in same application.

view full answer...

Answer 5

Since you have the MaxxFan model 00-4000K the correct circuit board replacement part number from us is the part #MA10A21276K.

view full answer...

Answer 6

The model number for fans such as the MaxxAir MaxxFan Mini Roof Vent, #MA00-04401M is listed on the upper side of the assembly itself. Please see the attached image. You will best identify this by opening the vent and climbing on top of the RV.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Lift Arm & Operator Mechanism For MaxxAir 4801K

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching