Recommended A-Frame Tool Box That Fits On Stromberg Carlson Trailer Cargo Carrier CC-255

Question

Question:

Is there an A frame tool box that will fit into a stromberg-carlson tongue mounted storage tray?

asked by: Michael J

1

Helpful Expert Reply:

There sure is!

The RC Manufacturing T-Series Trailer Tongue Tool Box - A-Frame - Aluminum - 2.6 Cu Ft in Silver # 350970 or Black # 350980 will fit in perfectly in your Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs # CC-255.

I included videos of the products mentioned for you to take a look at.

expert reply by: Samuel C

1

Answer 1

Yes, I pulled the Stromberg Carlson Trailer Cargo Tray Cargo Carrier #CC-255 and test fit it with the Buyers Products Utility Storage Box #3371712230 to find that they fit together. The base of the toolbox measures 29" long x about 14-3/4"…

view full answer...

Answer 2

Yes, you can use a generator and leave it installed on the Stromberg Carlson Tray #CC-255. Just make sure you have the generator grounded properly, which is specific to which generator you have but will be listed in it's owner's manual.…

view full answer...

Answer 3

Hey Joe, welcome back! I'm not entirely sure where our 15" measurement came from but you will be able to add your 13" diameter tank to the inside of the #3371701385. The front to back measurement is 16.16" and then the lip will…

view full answer...

Answer 4

Hey Ken, thanks for reaching out! The correct part you need is the Tekonsha Plug-In Wiring Adapter #3024-P for your 2025 Ram 1500. This is a pretty new fit listing which is why you're having trouble finding a confirmation on what you need.

view full answer...

Answer 5

Hey George, 6 inches of drop like what the Andersen WD system part #AN53VR is capable of is normally enough for most towing setups that need a decent amount of drop but it really comes down to what your trailer needs. To determine that you would need…

view full answer...

Answer 6

Hey Jack, you'd probably want to go with the more universal style of RV roof vent cover part #MA00-933066 as this was designed to fit basically all roof vents. We don't have any that would fit directly to your Ventline mounting tabs at this…

view full answer...

Answer 7

We likely have a toolbox which will work with your Aluma 548 trailer although A-Frame toolboxes are not made specifically to fit certain trailers so you will need to know the amount of room you have to fit the box. I do recommend going with a plastic…

view full answer...

Answer 8

Though the UWS A-Frame Trailer Toolbox - 6.3 cu ft - Gloss Black #UWS01065 will measure 49 inches at the back, 24 inches at the front, 18 inches deep, and 21 inches tall, I cannot suggest using it as a propane tank case. This is due to propane tanks…

view full answer...

Answer 9

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 10

Hey Wes. The Ventline Northern Breeze Roof Vents have been discontinued and we do not have an of the replacement operator parts. None of our vendors have anything either. The only option I have for you is to replace it with a comparable roof vent.…

view full answer...

Answer 11

I have included a diagram that shows the location of some screws that attach the screen frame and the upper housing (fan shroud) to the flange. That may allow you to access the area you are needing to look at. The Ventline Northern Breeze is a…

view full answer...

Recommended A-Frame Tool Box That Fits On Stromberg Carlson Trailer Cargo Carrier CC-255

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching