Bearing Buddies that Fit Malone Kayak Trailer # MPG550-AH

Question

Question:

Can you tell me if this comes with greaseable caps on hubs? if not can you recommend best option for water Thanks

asked by: Doug S

0

Expert Reply:

The spindles of the Malone trailer # MPG550-AH are not EZ lube so you'd be able to install Bearing Buddies like the part # BB1980A for chrome or part # BB1980A-SS for stainless steel. We have confirmed that these are the correct size as well.

expert reply by: Jameson C

0

Answer 1

Hey Ed, welcome back! The hubs on your Malone XtraLight Kayak Trailer have a 1.98" hub bore diameter. The Bearing Buddy Bearing Protectors #BB1980A you looked at are the correct size and fit. We also have the stainless steel version #BB1980A-SS.…

view full answer...

Answer 2

I spoke with Malone about which Bearing Buddies you should use on the Malone EcoLight Sport Trailer with V-Style Carriers for 2 Kayaks #MAL43FR and they said that they do not recommend using Bearing Buddies on any of their trailer, however if…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Bearing Buddies that Fit Malone Kayak Trailer # MPG550-AH

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching