Replacement Trailer Brake Shoes/Lining for Dico 10 x 2-1/4 Hydraulic Trailer Brakes

Question

Question:

i have the dico 60 hydrolic brakes on my boat trailer and i need some replacement shoes, not sure what i have seen on your sight is for the free reversing brakes. they are the 10x21/4

asked by: Ted

0

Expert Reply:

Since you do not have free backing brakes you will need to use replacement shoe/lining # BP04-120. This is for one wheel. For a whole axle you will need to order 2. These parts will fit on Atwood, Bendix, Dexter, and Dico 10 X 2-1/4 hydraulic brakes.

expert reply by: Michael H

0

Answer 1

The leading brake shoe on the #BP04-120 is the shorter shoe. The trailing shoe is the longer of the two.

view full answer...

Answer 2

All of our bearing kits, like the part #BK2-100 that was referenced, only include the inner/outer bearings, grease seal, and cotter pin/washer but I can help you get the other parts that you are needing as well. For 10" x 2-1/4" brakes we…

view full answer...

Answer 3

The brake mounting bolt pattern for the #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles #TRU87FR is 2-13/16" and then the section that fits into the axle tube is 2" and it tapers out to 2-3/8". Attached are dimensional…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Trailer Brake Shoes/Lining for Dico 10 x 2-1/4 Hydraulic Trailer Brakes

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching