SumoSprings Solo Custom Helper Springs - Rear Axle SSR-290-54 For Chevy P Chassis

Question

Question:

Where can I find the recommended air preasures associated with the SumoSprings Solo Custom Helper Springs - Rear Axle Item # SSR-290-54? What is the minimum? What is the min/max opperating range?

asked by: Jason B

0

Expert Reply:

The SumoSprings Solo Custom Helper Springs - Rear Axle # SSR-290-54 are actually jounce-style springs which do not require inflation. This particular system is rated for 2,800lbs. I really like this design because it offers a completely maintenance-free solution for reducing rear sag on your vehicle. Since this will level your vehicle, you will have evenly-distributed traction to all tires. This installs very simply by replacing your factory bump stop. You will want to go to the vehicle fit guide on our site and enter in your vehicle's information to verify which suspension enhancement system is for you, or you can provide me with the information and I will find a kit suitable. This kit is used on a lot of motorhomes that have the Chevy P chassis.

expert reply by: Andrew N

0

Answer 1

The SumoSprings Custom Helper Springs Kit #SSF-280-47 does not come with a spacer and #SSR-290-54 does come with a 1/2 inch spacers.

view full answer...

Answer 2

The SumoSprings Solo Custom Helper Springs #SSR-290-54 are 5" tall and 4" wide. The kit does include a 1/2" spacer which is to be used during installation so you will have a total height of 5-1/2".

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Donald, for the front axle of your 2019 Ford E-450 RV the SumoSprings kit part #SSF-106-47 is what you will want. This will provide the front suspension an additional 1,000 lbs of suspension support which will help with handling and sway…

view full answer...

Answer 8

Hey Alex, thanks for the picture! There's two options for Timbren setups that fit your 2019 Ford Transit T250 and either one of them are really going to help support the rear end of your van when it's loaded up. Which one you need is going to…

view full answer...

Answer 9

Hi Aaron, I can understand not like the TImbrens as those can definitely be rough on a pretty consistent basis; you made a nice choice for your 2024 Ram 3500 by instead going to the SumoSprings Solo Custom Helper Springs #SSR-312-54. The #SSR-312-54…

view full answer...

Answer 10

Hello Andrew, Well that sounds like quite the fun trip, what state or states will you be traveling through? You're asking a really important question, especially since you're planning a cross-country trip with about 250 pounds of bikes and…

view full answer...

Answer 11

According to my research, your 2001 Airstream Land Yacht 30 is on a P-30 Workhorse Chassis. If this is the case then I do have an option for you but SuperSprings does not offer a set SumoSprings Solo Custom Helper Springs that will work on the front…

view full answer...

Answer 12

If it were me I would install the Timbren springs #TFREXC4 on the 2000 Ford Excursion 4x4 instead of the SumoSprings #SSR-109-40. First is the cost benefit; the Timbren springs cost less. There is also the capacity difference. The Timbren springs are…

view full answer...

SumoSprings Solo Custom Helper Springs - Rear Axle SSR-290-54 For Chevy P Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching