Replacement Mounting Bracket for Valley Odyssey 52810 Brake Controller

Question

Question:

Hello, Could not find an phone number. I have a Valley Odyssey 52810 brake controller. The bracket broke and Valley does not appear to make brake controllers any longer. The controller is 3.263 W so 3.25 inside for the bracket and 1 from inside of bracket to screw hole clearance needed. I can drill this. Do you have anything I can use?

asked by: Scott H

1

Helpful Expert Reply:

The closest option we have to what you are looking for is part # P7685, which measures 3-3/16 inches inside width.

expert reply by: John H

1

Answer 1

You have hit the nail on the head regarding the necessary equipment. Getting 2 to 3 years out of a wiring harness is not unheard if. As with all electronics, they have a limited lifespan. You will want to examine the wiring on the trailer you pulled…

view full answer...

Answer 2

Yes, if you're trying to replace your original Tekonsha Prodigy brake controller (obsolete part number 90185), the Prodigy P2 #90885 will plug right into the same 4-pin wiring adapter, like #20127. Both use mounting bracket #P7685 and pocket…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Replacement Mounting Bracket for Valley Odyssey 52810 Brake Controller

Continue Researching