Install Kit for Westin Bull Bar on 2010 Nissan Frontier

Question

Question:

I need an installation kit for Westin ultimate bull bar with skid plate-3 inch tubing - chrome- plated stainless steel to be mounting on 2010 Nissan frontier , do you have this kit and what part # would be, thank you so much Nissan frontier 2010 crew cab

asked by: Luiz

0

Expert Reply:

I spoke with my contact at Westin, who tells me that the Bull Bars are somewhat vehicle-specific. The only Bull Bar that is compatible with the 2010 Frontier is the # 32-1695 in black powder coated steel. The hardware kit is part # 32-169PK, and is specific to the #32-1695.

The Westin # 31-5170 you mentioned is only compatible with the GM Trucks and SUVs listed on the bottom of the product page.

expert reply by: Mike L

0

Answer 1

We have the Replacement Install Kit #AA36FB for the Black #AAB35-9002 or Stainless #AA35-9002 Aries Bull Bar which fits your 2013 Nissan Frontier. We also have the Replacement Install Kit #32-169PK for the Westin Ultimate Bull Bar #32-1695.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 7

If nothing is noted on the axle or outside of the brakes for the front or rear, you can remove the front hub and take a look at the brakes. The magnet is always on the bottom of the assembly and the actuating arm for the brakes always bows toward the…

view full answer...

Answer 8

The easiest way to tell if a trailer brake assembly is installed on the correct side of the trailer is to pull the hub off and look at the actuating arm. The arm should be in front of the spindles on the side closer to the front of it. See attached…

view full answer...

Answer 9

The braking performance will not be very good if you install brake assemblies on the wrong side of the trailer. The left side assembly is the driver's side (if the trailer were a car) and the right side is the passenger's side. The actuating…

view full answer...

Answer 10

If you look at the wheel cylinder of the brake assemblies part #23-399 and #23-398 you'll see the letters L and R stamped on them. The R means right hand side and L means left. I attached a picture that points out the letter. Right side means…

view full answer...

Answer 11

The left side is the driver side, right side is passenger side. On a trailer brake assembly like #23-105 the arm that the magnet is on points to the front of the trailer and the magnet always will be on the bottom. I have included a picture that…

view full answer...

Install Kit for Westin Bull Bar on 2010 Nissan Frontier

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching