How To Determine Compatibility with RV LED Light Side-Slide Dimmer Switch

Question

Question:

Hello! I’m wondering if this switch is compatible with the Dream Lighting 12V LED Dome Light Fixtures found in current year Winnebago Minnie Winnies.

asked by: Griffin S

0

Expert Reply:

The RV LED Light Side-Slide Dimmer Switch part # 37205-12315 is a universal dimmer designed to be used with LEDs. It's not specific to any one particular light brand/model. If the light uses LEDs it should work just fine.

expert reply by: Conner L

0

Curt W.

11/3/2021

HI. I have a 2021 Cougar 25RDS. I purchased the 37205-12315 switch, hooked it up per your video and directions. It will turn the 3-lights in my slideout On and Off, but no dimming. I returned the switch and you sent me a new one. Same problem. I'm really stuck here. I would include a photo but that doesn't seem to work on this. I have Red to Red (and the red wire was hot and the lower wire on the switch. I have 2 green wires that go to the lights (they were the upper connector on the switch) and I connected the White wire to that. The black wire goes to the 3 white wires that are crimped together. I sure could use some help. 904.571.1475

Les D.

11/4/2021

Few LED lights are dimable. Is this a stock light from the factory, or a light you bought from us? Most incandescent (standard) bulb and halogen bulb fixtures will work with most dimmer models but lights using LED elements typically do not work with dimmers. LED bulbs either dim insufficiently, flicker, or they don't light at all when fed power through a dimmer switch.

Answer 1

Since your MaxxFan Roof Vent, like the MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan #MA00-03851 will turn on, but won't turn off, it sounds like your circuit board. I recommend replacing your circuit board with the Replacement Printed Circuit…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

How To Determine Compatibility with RV LED Light Side-Slide Dimmer Switch

Product Page this Question was Asked From

Continue Researching