Snatch Block to Use with Bulldog Winch part # BDW15020

Question

Question:

Bulldog Winch Trailer Winch - Synthetic Rope - Hawse Fairlead - 4,400 lbs Item # BDW15020 Looking to purchase Snatch Block to use with winch. Any recommendations for which one would work best.

asked by: Lester H

0

Expert Reply:

The Bulldog Winch Snatch Block # BDW20005 would work great with the Bulldog Winch part # BDW15020 as it has more than enough capacity and was designed for use with synthetic rope like the winch has.

expert reply by: Jameson C

0

Answer 1

According to the folks in the engineering department at ComeUp, the #CU881081 does have a safety 'cushion' on top of the stated 6000 lb capacity, but they won't say what that figure is for liability reasons. For example, if the failure…

view full answer...

Answer 2

Since you are getting a car hauler trailer and will be pulling vehicles onto it that means you will have rolling loads. A rolling load is much easier to move than a static load so you do not have to have a high capacity winch. When winching a rolling…

view full answer...

Answer 3

You can use a pulley block like part #BDW20005, to pull your car on to a trailer with the winch being offset. You will want to make sure the winch is well secured for safety. This pulley block has a capacity of 17,000 lbs break strength and is…

view full answer...

Answer 4

We have pulley blocks like the #BDW20023 that could be used in your application but you'd have to come up with a way to mount them since we don't have setup designed for your application.

view full answer...

Answer 5

The Superwinch #1120210 LT2000 you referenced would be perfect for your needs. According to my calculations, the ramps you are using have a bit more than a 40 percent grade. According to the table shown in the FAQ article I have linked you to, the…

view full answer...

Answer 6

It sounds like you're looking for a pulley block like part #BDW20004. I would think some sort of D-ring tied into the frame of the trailer would provide a good mount for the pulley block. I looked through our selection of D-rings, and the highest…

view full answer...

Answer 7

3/16 inch diameter wire rope is a standard winch cable size like what the ComeUp Snatch Block part #CU881080 was designed to work with so this would work great.

view full answer...

Answer 8

A Superwinch LT2500 has a 2500 lb line pull capacity. For a rolling load like a car with fully inflated tires, a winch with a capacity equal to the weight of the vehicle, in your case 4000 lbs is recommended. This means that your winch has about half…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Snatch Block to Use with Bulldog Winch part # BDW15020

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching