Tire Chain Recommendation for Tire Size 285/75R18

Question

Question:

Good morning, I was wondering if you could point me in the right direction for tire chains and tensioners. These would just be for the rear of my 17 Tundra. I have a lift so tire size is AT 285/75/r18 that I would need to fit. Thank you

asked by: Evan W

0

Expert Reply:

For your tire size of 285/75R18 the Titan tire chains part # TC2536 would be a really great option which have tensioners built in. These install easily, provide great traction, and are priced great too.

expert reply by: Jameson C

0

Answer 1

Hey Erick, yes the EcoHitch front hitch part #EH39CR that you referenced does fit your 2026 Ford F-250 with the Tremor package.

view full answer...

Answer 2

For your size 285/75-18 tires, the best option for snow tire chains are from Titan, at the following part number: - Titan Chain Snow Tire Chains w/ Cams for Wide Base Tires #TC3831CAM There are a number of reasons I really like the #TC3831CAM,…

view full answer...

Answer 3

Hey Geroge, The advantage of the EcoHitch #EH39CR over the Draw-Tite #65076 for your 2025 Ford F-350 Super Duty is that the receiver sits up higher so you get better clearance for your accessory and you don't lose any ground clearance. The…

view full answer...

Answer 4

Yes, we have two hitches that fit your 2020 Ford F-250; the Draw Tite part #65076 and the Curt #C31078. The difference is that the Curt will not stick out far past the air dam. I have attached a picture of the Curt showing this. Also the Curt is made…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 9

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 10

Hey Doug. So long as your Husky 5th wheel hitch isn't three decades old you shouldn't have any issues attaching it to the B&W Custom Installation Kit w/ Base Rails item #BWRVK2402. Most 5th wheel hitches for the last 20 years have used…

view full answer...

Answer 11

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 12

Hey Liz. The cameras of the Furrion Vision S+ item #FR64AD will need to be wired directly to a constant 12v power source, like your Grand Design's batteries, to use them in the security mode. With the infrared lights on each camera will pull less…

view full answer...

Tire Chain Recommendation for Tire Size 285/75R18

Product Page this Question was Asked From

Continue Researching