Recommended Winch To Replace Discontinued Shelby Model 5400 Single-Speed Winch

Question

Question:

I need two Shelby Model 5400 wenches but I found out Shelby is out of business. Do you have a recommendation for a replacement wench. I want the same bolt hole pattern if at all possible. Thanks

asked by: Stan G

0

Expert Reply:

I do have a recommendation for a winch that will have the same bolt pattern and 400lb weight capacity as your discontinued Shelby Model 5400 winches.

I recommend the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 12' Strap - 400 lbs # DL16003 which is very similar to your Shelby 5400s, and includes a 2" wide x 12' long strap.

Mounting hardware is not included, so if your current mounting hardware is in bad shape you will need to find the correct replacements at your local hardware store.

I included a video of the # DL16003 for you to take a look at.

expert reply by: Samuel C

0

Peter M.

6/8/2025

I can’t find this winch to order it. Can you help me find it. Dutton-Lainson Trailer Winch DL16003

Jameson C.

6/9/2025

@PeterM That specific winch is no longer available but we have the pretty similar Buyers Products part # 337HW800S which would work great instead.

Answer 1

The Dutton-Lainson Hand Winch part #DL15303 is the replacement that I recommend for your Shelby Hand Winch 5405. These winches both have the same 1,400 lb capacity and overall size. In regards to mounting, most hand winches now use a standard pattern…

view full answer...

Answer 2

I have attached a full dimensional drawing for the #DL64FR below which includes the base hole pattern. This winch has an 800 lb capacity and comes with a 5-year warranty.

view full answer...

Answer 3

Unfortunately since Shelby is out of business, I would not know if the bolt would be able to come out or not, and trying to find replacement parts anywhere is difficult. I would recommend getting a new winch. The Dutton-Lainson Hand Winch #DL16003,…

view full answer...

Answer 4

The best option to replace your current Shelby Winch would be to use a winch like the Dutton-Lainson Hand Winch, Single Speed, #DL15303. This winch has a 1,400 lbs horizontal pulling capacity and has the zinc Tuffplate finish for rust and corrosion…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended Winch To Replace Discontinued Shelby Model 5400 Single-Speed Winch

Featured Help Information

Miscellaneous Media

Continue Researching