Base Hole Pattern for Dutton-Lainson Hand Winch DL64FR

Question

Question:

what is tyhe hole mounting pattern, dimensions?

asked by: Steve H

0

Expert Reply:

I have attached a full dimensional drawing for the # DL64FR below which includes the base hole pattern. This winch has an 800 lb capacity and comes with a 5-year warranty.

expert reply by: Robin H

0

Dutton-Lainson 14914 Dimensional Drawing.
(click to enlarge)

Answer 1

The Dutton-Lainson Hand Winch part #DL15303 is the replacement that I recommend for your Shelby Hand Winch 5405. These winches both have the same 1,400 lb capacity and overall size. In regards to mounting, most hand winches now use a standard pattern…

view full answer...

Answer 2

I do have a recommendation for a winch that will have the same bolt pattern and 400lb weight capacity as your discontinued Shelby Model 5400 winches. I recommend the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 12' Strap - 400…

view full answer...

Answer 3

For a wooden bunk trailer the rule of thumb is to go with a winch that has a rating that is at least 50 percent of the weight of the boat. Let's say your boat weighs a total of 2,500 lbs when totally loaded up and counting the weight of the…

view full answer...

Answer 4

Winches like the Dutton-Lainson #DL14830 you asked about have mounting holes that tend to resemble a Picasso painting so they can be hard to describe. Instead I made a diagram that shows the majority of the bolt hole spacing. If you need a specific…

view full answer...

Answer 5

I attached links to this page that have all of the dimensions for the Fulton F2 Trailer Winch #FW32000101 that you referenced. When looking at it from the front the winch will have an overall width of 14.77", which includes the extension from…

view full answer...

Answer 6

It can definitely be a very confusing subject when trying to determine the correct size winch and strap for your boat. The important thing to remember is that you are not lifting the entire weight of the boat but rather pulling it across the bunk…

view full answer...

Answer 7

Thank you for that info, and while we have some options for you to replace your Shelby 5764A trailer jack, there isn't one that is going to fit that bolt pattern. So you have a couple of things you can do, which is either have a new plate welded…

view full answer...

Answer 8

We offer weld-on and bolt-on trailer jacks that are similar to the Shelby 5764A jack you wish to replace but the jacks we offer are not exact replacements. We do have a jack that has a mounting plate similar to the Shelby mounting plate., It is part…

view full answer...

Answer 9

We do have trailer coupler locks you can use, but if your coupler doesn't have a pin hole, there isn't a way to lock it while it's attached to your vehicle's hitch ball; it will need to be uncoupled for a lock to be put on. Once you…

view full answer...

Answer 10

I do have an option for you but Shelby boat trailer jacks are discontinued and we don't offer any direct bolt-on replacements for them. That said, you can easily remove the old flange by cutting or simply place the new jack beside it and leave…

view full answer...

Answer 11

I recommend using the Xtreme Off-Road Swing-Up Trailer Jack #ORJW350D as we do not have a jack which will fit the same weld on bracket you have on your boat trailer. This jack can be bolted onto your frame and will allow you to have more…

view full answer...

Answer 12

I can definitely point you in the right direction of a new winch. Unfortunately Shelby is no longer in business, so a direct replacement is out of the question. That being said we have come across these Shelby 5405 winches before, and have found the…

view full answer...

Base Hole Pattern for Dutton-Lainson Hand Winch DL64FR

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching