Is There An Adapter Kit To Fit 59 Rhino Rack Ladder Roller To Rhino Rack Vortex Cross Bars

Question

Question:

will the Rhino Rack Ladder rack roller #RR1500 fit on a Rhino Rack Vortex cross bar? If not is their an adapter kit? thank you

asked by: Mike M

0

Expert Reply:

I recommend using two of the Ladder Roller for Rhino-Rack Aero/Sportz Crossbars Item # SR680. We do not currently offer a kit to adapt the 59" ladder roller Item # RR1500 to Vortex Aero Crossbars Item # Y02-490B-NT.

expert reply by: Shane H

0

Answer 1

Hey Brian, thanks for reaching out. I went out to our warehouse and measured one of the etrailer Sidewind Aluminum Jacks #e95YV. The distance from the center of the bracket to the bottom of the wheel is approximately 14" with the jack fully…

view full answer...

Answer 2

Hi, Aaron. Yes, the LockRack Ladder Rack Base Set with Upright, part #LR96FR, is compatible with the Rhino Rack Sportz roof rack, including the Sportz crossbars in part #RR43HG for the 2024 GMC Sierra 2500 crew cab or double cab with a naked roof.…

view full answer...

Answer 3

Hi Robert, The Ladder Roller for Rhino-Rack Heavy-Duty Crossbars #RR1500 will sit level with the crossbars when it is attached.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Is There An Adapter Kit To Fit 59 Rhino Rack Ladder Roller To Rhino Rack Vortex Cross Bars

Products Featured in This Question

Continue Researching