How to Mount Yakima TopWater into T-Slot Channels on Crossbars or Roof Platform with T-Slots

Question

Question:

Will the Yakima fishing rod carrier mount to the Rhino roof carriage platform? I have a 2019 GMC Yukon Denali with cross bars.

asked by: Stu M

0

Expert Reply:

In order to mount a Yakima TopWater Rooftop Fishing Rod Carrier - Locking - 8 Fishing Poles # Y04088 to a Rhino Rack Pioneer Platform like the # RR42114BF you'll need to use the SmarT-Slot Mounting Kit for Yakima TopWater Rooftop Fishing Pole Carrier # Y04094. This will allow you to mount the TopWater in the T-slot channels that are on the Pioneer platform.

You are also able to mount these directly to your factory crossbars without the Pioneer platform attached using the included hardware.

expert reply by: Erik B

0

Answer 1

Hey Dave, the Yakima Rod Carrier part #Y04089 does require that rods longer than 7 feet need to get broken down. This is a cautionary statement due to the flex of rods on that forward clamp. Some rods may have too much flex from the headwinds and…

view full answer...

Answer 2

Hey Brosnon! I wasn't able to find the exact dimensions of those crossbars so I can't say for sure. We have seen both clamped onto ladder racks so more than likely it won't be an issue. However, it does look like they have channels on…

view full answer...

Answer 3

I don't believe your two 30 inch wide kayaks will fit on the bottom deck of the Yakima EasyRider Double Decker Trailer #Y08129 . I confirmed through my contact at Yakima that the width of the bottom deck is 54 inches inside to inside of the 2…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

How to Mount Yakima TopWater into T-Slot Channels on Crossbars or Roof Platform with T-Slots

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching