Is Male Pipe for etrailer and Ram Pipe Mount Swivel Jacks Available

Question

Question:

I am looking at TJP-OP916 the female end. Do you also have one identical to this but a male end? THanks,

asked by: Bill

0

Expert Reply:

We do. You need part # TJP-IP916 for the male pipe that fits with the female # TJP-OP916.

expert reply by: Charles S

0

Answer 1

The female version of the Bulldog Replacement Pipe Mount for Swivel Jacks #BDPQM1900 isn't available separately and only comes already installed on the trailer jacks, like what we see with part #BD195362. If you're needing a weld-on bracket…

view full answer...

Answer 2

We have just the thing! The Replacement Male Pipe #TJP-IP916 is going to be the correct weld-on male pipe mount for the #TJP-5001S-B jacks. If you need the female side to weld to the jack itself it will be part #TJP-OP916.

view full answer...

Answer 3

Hey Martin, The Replacement Male Pipe for Curt Pipe Mount Swivel Jacks #C46FV has a 2" outer diameter which is pretty standard for pipe-mounted swivel jacks so it would likely be a fit. I wasn't able to confirm the female side of this on the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Is Male Pipe for etrailer and Ram Pipe Mount Swivel Jacks Available

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching