Can the Reese Dual Cam High-Performance Sway Control Be Added To Reese System RP66022

Question

Question:

Can a reese 26002 dual cam sway control be added to 66022 weight distribution hitch?

asked by: James W

0

Expert Reply:

Yes, you can add the Reese Dual Cam High-Performance Sway Control part # RP26002 to the Reese Weight Distribution System part # RP66022. This will give you the Strait-Line Weight Distribution System part # RP66074.

expert reply by: Conner L

0

Answer 1

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 2

The great thing about weight distribution shanks is that for the most part they are cross-compatible therefore you can mix and match brands. The Equal-i-zer Weight Dist Shank part #EQ90-02-4300 offers up to 6" of drop and there should be no…

view full answer...

Answer 3

Yes, we do offer replacement trunnion bars for weight distribution (WD) systems like the Reese #RP66022 that you referenced. You can click on the link provided to see all replacement trunnion bars for Reese and other brands. You will want to choose…

view full answer...

Answer 4

The answer to your question is a solid maybe. In order to have the correct amount of drop you need to measure from the ground to the top inside of the hitch receiver on your truck, and then from the ground to the bottom of the coupler on your…

view full answer...

Answer 5

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 6

If your current weight distribution system is less than 3 years old, then you will be able to use the Replacement Trunnion Spring Bar, #RP66009. If it is the old style system, the bars will not fit in the head. The head you would need is #RP58167.…

view full answer...

Answer 7

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 8

The Reese Strait-Line Weight Distribution System w Sway Control #RP66084 is it's one ball mount. You will simply need to choose a hitch ball that matches the size of the coupler on your trailer. You can use part #A-90 if you need a 2 inch…

view full answer...

Answer 9

Hey Eric, I went ahead and got in touch with ProPride, and they confirmed that yes the ProPride 3P Weight Distribution Hitch w/ Sway Control for 2-1/2" Receivers #PR47QR will work with underslung couplers.

view full answer...

Answer 10

Weight distribution hitches are classified by the range of trailer tongue weights their spring bars are rated for. If your current weight distribution hitch like the #RP66022 you'd looked at is rated for up to 12000 lbs, then the bars would be…

view full answer...

Answer 11

Yes the Reese Weight Distribution w/out Shank #RP66022 that you referenced is perfectly compatible with the 2-1/2 inch shank part #RP54977 that you also referenced.

view full answer...

Answer 12

To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind…

view full answer...

Can the Reese Dual Cam High-Performance Sway Control Be Added To Reese System RP66022

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching