Replacement A-Frame Coupler Latch Differences

Question

Question:

What is the difference between the latch F640801 and the F670801. Need a replacement for a bumper pull 2006 TrailsWest 2 horse trailer.

asked by: Jodi D

0

Expert Reply:

The difference in the Repair Kit for Fulton A-Frame Coupler 2-5/16" Ball with Wedge-Latch part # F640801 and the Repair Kit Fulton Wedge-Latch Cast Head Coupler part # F670801 is what couplers they fit.

Part number F640801 is designed for use with the standard F44305R0317 and F44305R0500 couplers and the F670801 is for use with the cast iron 44125W and 44150W series couplers

expert reply by: Randy B

0

Answer 1

We don't have a confirmed fit for your Fulton Coupler for a repair kit. The Latch Repair Kit #F670801 is the closest option we have and hasn't been tested with straight couplers so I can't confirm it will work. I recommend instead for a…

view full answer...

Answer 2

The coupler repair kit for the Bulldog Cast Head Coupler, #BD4425000317, is part #F670801.

view full answer...

Answer 3

Jon, the Repair Kit Fulton Wedge-Latch Cast Head Coupler #F670801 is designed to work with select 2 5/16" couplers so it's not going to work with your 2" coupler. Even if it worked with 2" couplers, it'd still be unlikely that…

view full answer...

Answer 4

I spoke with my contact at Bulldog and he confirmed that for coupler #BD4420000317 you would use latch repair kit #F670801. This repair kit actually fits several makes and models of couplers from Fulton and Bulldog.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Replacement A-Frame Coupler Latch Differences

Continue Researching