Latch Repair Kit for Bulldog Cast Head Coupler 4420000317

Question

Question:

a replacement wedge and latch availble for this hitch

asked by: Ray D

0

Expert Reply:

I spoke with my contact at Bulldog and he confirmed that for coupler # BD4420000317 you would use latch repair kit # F670801. This repair kit actually fits several makes and models of couplers from Fulton and Bulldog.

expert reply by: Michael H

0

Answer 1

The difference in the Repair Kit for Fulton A-Frame Coupler 2-5/16" Ball with Wedge-Latch part #F640801 and the Repair Kit Fulton Wedge-Latch Cast Head Coupler part #F670801 is what couplers they fit. Part number F640801 is designed for use with…

view full answer...

Answer 2

The coupler repair kit for the Bulldog Cast Head Coupler, #BD4425000317, is part #F670801.

view full answer...

Answer 3

Jon, the Repair Kit Fulton Wedge-Latch Cast Head Coupler #F670801 is designed to work with select 2 5/16" couplers so it's not going to work with your 2" coupler. Even if it worked with 2" couplers, it'd still be unlikely that…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Latch Repair Kit for Bulldog Cast Head Coupler 4420000317

Featured Help Information

Miscellaneous Media

Continue Researching