Bearing Kit for Dexter D52 with Bearings 14125A/25580 and Seal with ID of 2.250 inch

Question

Question:

Im wondering which bearing kit to buy as a spare. My axles are Dexter D52-8 and I know some bearing information. Grease seals: 22333TB ID: 2.25 OD: 3.376 Inner bearing: 25580 Outer bearing: 14125A Thanks,

asked by: Joel G

1

Helpful Expert Reply:

The exact bearing kit you need is the part # BK3-200 which comes with outer bearing 14125A, inner bearing 25580, and grease seal 10-36 which matches the inner diameter you need of 2.250 inch.

expert reply by: Jameson C

1

Answer 1

The correct replacement grease seals for your #22333TC seals is part #RG06-070. This includes two double lip seals and they have the same inner diameter, outer diameter and thickness as your current seals. To replace your brake assemblies on your…

view full answer...

Answer 2

Hey Johnny, we have the wheel stud part #DE52GR that matches what you are looking for with the knurl diameter of .545 inch and a thread size of 1/2 - 20. The overall length is 2 inch too. What hub do you have?

view full answer...

Answer 3

The Dexter Trailer Hub and Drum Assembly #42866UC3-EZ is the correct one for your axle. It includes the hub/drum assembly complete with inner and outer bearings and races. New lug nuts, grease seal, grease cap, spindle nut and lock are also…

view full answer...

Answer 4

I was unable to find any information with the numbers on your axle, unfortunately. However, you can contact the manufacturer of the trailer and they should be able to tell you exactly which inner and outer bearings you have. If for some reason they…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Bearing Kit for Dexter D52 with Bearings 14125A/25580 and Seal with ID of 2.250 inch

Product Page this Question was Asked From

Continue Researching