What is the Difference in the Demco Hydraulic Brake Line Kit Part # DM5427 and Part # DM5426

Question

Question:

What is the difference between Kit #DM5427 and Kit #DM5426?

asked by: Steve

1

Helpful Expert Reply:

The Demco Hydraulic Brake Line Kit for Single Axle Trailers part # DM5427 and Demco Hydraulic Brake Line Kit for Single Axle Trailers part # DM5426 are almost identical.

The only exception being one of the steel brake lines in the DM5426 kit is 80" and in the DM5427 kit it is 72". Everything else is identical. Same hoses, lines, keepers, screws and hardware.

I have linked a video my buddy Shano did of the kit if you would like to check out how it all works together.

expert reply by: Randy B

1

Answer 1

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 2

Hey Howard! Yes, I think the Replacement Inner Member for Dexter DX7.5L Brake Actuator #DX97FR will replace what you have. It has the same body, just a different coupler on the end, so it will line up in the old housing. If you want to save some…

view full answer...

Answer 3

Hey Oscar, yes you can use a Curt tow bar like the Rambler part #C25DQ with a Blue Ox base plate kit like the part #BX3620 that you referenced. Do you have a Curt tow bar already? What are you flat towing?

view full answer...

Answer 4

I do not see an extension kit for the Demco Hydraulic Brake Line Kit for Single Axle Trailers #DM5426. However, you can just step up to the Demco Hydraulic Brake Line Kit #DM5643 which has the additional main line (long run) length that you are…

view full answer...

Answer 5

Hey Robert. The side bolts with the grease fittings should be tight on the Dexter DX7.5 Drop-N-Go Brake Actuator item #099-175-20. They're not holding the actuator on but you don't want the nuts backing themselves off. What kind of trailer do…

view full answer...

Answer 6

In order to find out what you need for a replacement actuator you will want to start by finding out what kind of brakes you have. A different brake actuator is needed if you have drum brakes or disc brakes. You will also want to choose a replacement…

view full answer...

Answer 7

Hey Kellon, we can help you piece together a kit like the part #HYD22FR that includes the marine grade actuator but as a complete kit we don't have one with it. So the first thing you'll need is a marine grade actuator which we have with the…

view full answer...

Answer 8

Hello Keith, Yes, the Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs #DM72VR will work great for replacing the TDE-660 Hydraulic Actuator. The bolt holes are even 3" apart, just like the one you are replacing. The only…

view full answer...

Answer 9

The best replacement option we offer for an Atwood Surge Brake Actuator 85778 is the Demco Hydraulic Brake Actuator part #DM62VR. It has the same ball size, offers a bolt-on install, and has a greater capacity. The only functional difference is it…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

What is the Difference in the Demco Hydraulic Brake Line Kit Part # DM5427 and Part # DM5426

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching