Looking for Brake Line Kit for 2020 Bass Tracker 20 ft Boat Trailer

Question

Question:

2020 bass tracker 20 ft boat trailor hydrolic brake line kit

asked by: Nick P

0

Expert Reply:

Hey Nick, it sounds like your trailer is a single axle and you are needing a brake line kit for it. For that we have the part # DM5643 which has a 20 foot main line or the part # DM6097 which has a 15 foot main line.

expert reply by: Jameson C

0

Answer 1

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

The wires on the Reverse Lockout Solenoid Kit #DM5836 are for the ground and the reverse light circuit. It does not matter which wire you use for the two connections, it will work either way. If you take a look at the installation video below…

view full answer...

Answer 4

We offer both individual bearings, races, and seals as well as complete bearing kits in many common parts combinations. The best way to know what parts you need is to obtain the part numbers from the existing bearings and seals. The linked photo will…

view full answer...

Answer 5

The top bolts are 3 inches apart on center, and the bottom bolt is 2 inches underneath those (and directly in the middle of the top bolts) for the 7,000 lb Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc Brakes #DM62VR. You'll need…

view full answer...

Answer 6

Two bolts will be sufficient for installing the Demco Hydraulic Brake Actuator #DM72VR. You will want to use two Requires 2-1/2" x 4-1/2" Grade-5 of Grade-8 bolts. Personally I would use something like the Curt Coupler Hardware Kit #C25388.…

view full answer...

Answer 7

Hello Bruno, thanks for reaching out. The Demco #DM72VR can be used to replace your old Atwood 61101. The Demco actuator uses 3 holes and you will need to use all three holes for mounting. If your tongue only has two holes currently, a 3rd hole will…

view full answer...

Answer 8

You can certainly go ahead and re use the existing 2 bolts, provided they are in good condition. The fish wire method shown in the video works too, but it is also very common to just use the two bolts like your old Atwood actuator. Personally I would…

view full answer...

Answer 9

I have attached for you below a photo which shows the bolt pattern for the Demco Hydraulic Brake Actuator part #DM72VR.

view full answer...

Answer 10

Hi Chad! That 4 bolt mounting plate with 2-7/8" measurement is pretty much the standard for 3,500 pound axle brakes (which the Dexter 8-247 drum also fits), so that makes it nice and easy. We have a lot of option, but I recommend the two I have…

view full answer...

Answer 11

For 10 inch brakes like #AKUBRK-35-D you can use nut and lock washer set (8 each) #BRKH10B. If you want to source stainless or galvanized nuts locally then they should be 7/16"-20.

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Looking for Brake Line Kit for 2020 Bass Tracker 20 ft Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching