Which Dexter EZ Flex Kit for 2009 Weekend Warrior Triple Axle

Question

Question:

Is this kit the correct kit for my al-ko 6000lb axles? It’s a triple axle. Thanks

asked by: Jeff M

0

Expert Reply:

For a triple axle trailer with 6k rated axles the correct Dexter EZ Flex is the part # K71-656-00. The # K71-657-00 would be for 8k axles.

I attached an install video for this kit for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Dexter E-Z Flex Triple Axle Suspension Kit #K71-657-00 referenced in your question is designed for triple axle trailers and includes equalizers that measure 7-3/4 inches long. If your Weekend Warrior has 3 axles and the equalizer length matches…

view full answer...

Answer 2

The Keystone Carbon 417 should have a 35" axle spread which can be confirmed by measuring from the center of each axle. In which case, we have options from both Dexter and MORryde. The MORryde Rubber Equalizers for Triple Axle Trailers part…

view full answer...

Answer 3

Going with a slightly shorter shackle like the part #018-026-05 would not be an issue. The shackles will angle slightly flatter than the longer current shackles you have now but they'll still work fine.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Which Dexter EZ Flex Kit for 2009 Weekend Warrior Triple Axle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching