Wiring Diagram for Progressive Dynamics Converter # PD4135K

Question

Question:

Hello. I am trying to build out a trailer. I intend to have batteries in a TorkLift Power Armor Solar Locking Battery Cabinet. I also have a generator as a back up and to charge the batteries. Do you have a diagram that shows how I can wire the battery cabinet and the generator with the PD4135k converter.

asked by: Dillon T

0

Expert Reply:

I attached a wiring diagram for the Progressive Dynamics Converter # PD4135K for you to check out. On the right side of the diagram you'll see the connections that run to the battery and on the left side you see the connections that you'd run generator input power source.

expert reply by: Jameson C

0

click to enlarge

Rick

8/27/2024

It is my understanding that the 4135 converter will supply 12v dc even without being connected to a battery. Does the white wire on the back of the converter next to the 5 black 12v leads need to be connected to chassis ground if there is no battery

Jameson C.

8/27/2024

@Rick I'd go ahead and connect it even if you won't have a battery.

Rick

8/27/2024

@JamesonC I have been trying to figure out why my 12v lights are not working. Would this possibly explain why they are not working? I know when I add a battery, the white wire will go to the negative and the negative terminal will also be grounded to the chassis but without a battery, I did not realize that the white wire would need to be grounded since the converter is also grounded to the bus bar.

Jameson C.

8/27/2024

@Rick It's hard to say but it's worth trying. Most likely your lights aren't grounding properly and the wire being connected will complete the circuit.

Answer 1

The Red Label bags like the part #F2706 are much heavier duty than the standard duty bags like the #F2598 that you also mentioned. The pressure rating is 150 psi vs. 100 psi, the weight capacity is 7,500 vs. 5,000 lb, and overall they are just larger…

view full answer...

Answer 2

I have a solution for you because as you know what you have now cannot charge Lithium batteries. You will need the Progressive Dynamics #PD4135K which is designed to replace your WF-8735P and is compatible with Lithium batteries. When this is…

view full answer...

Answer 3

The main AC breakers of the #PD4135K should be 30 amp. As far as wiring we have to recommend you stick with Progressive Dynamics and consult a licensed electrician or RV tech for the wiring and install of the kit. On the panel with the fuses the left…

view full answer...

Answer 4

Yes, you do Dan! I checked the installation instructions, which I have listed below, and below the section that says DC ELECTRICAL on the second page it says to do exactly what you've asked. Please note that it is recommended to consult a…

view full answer...

Answer 5

The Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger, #PD4135K is a suitable replacement for your Magnetek 6612 converter, providing you have at least 8 gauge wire in serviceable condition. The #PD4135K is a…

view full answer...

Answer 6

When the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 35 Amp #PD4135K is placed in lithium mode it will provide a constant nominal voltage output of 14.6 VDC. There are numerous factors that will…

view full answer...

Answer 7

Yes, the Progressive Dynamics 4100 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel #PD4135K will also charge your batteries. This system has a built in charge wizard that will detect when your batteries need charging and will…

view full answer...

Answer 8

There is a switch on the Progressive Dynamics 4100 Series RV Converter w/ Charge Wizard #PD4135K that will allow you to switch it from the 13.6 volt output for lead acid batteries to the 14.6 volt output when switched to lithium charge mode. This is…

view full answer...

Answer 9

Yes, all you'll need to do is disconnect the three wires running from the converter section in your Progressive Dynamics 4100 #PD4135K from the AC distribution panel (circuit breaker, ground bus bar, neutral bus bar). This will cut the power…

view full answer...

Answer 10

The Winntec 6020 is an automatic changeover regulator, and the best option we have to replace it is with one from Camco, which is the following part number: - Camco Automatic Changeover 2-Stage Propane Regulator for Dual Propane Tanks #CAM59005 This…

view full answer...

Answer 11

The battery charger output of the Progressive Dynamics Charger/Converter #PD4135K that you referenced is 35 amps 12 volt. This also equals 470 watts but typically in 12 volt battery charger applications amperage is listed instead of wattage.

view full answer...

Answer 12

We have the Progressive Dynamics Converter/Smart Charger at 35 Amp, #PD4135K. This is a replacement for WFCO WF-8735 that works with lithium-ion, flooded lead acid, AGM, and gel batteries. Please note the attached product review video and follow the…

view full answer...

Wiring Diagram for Progressive Dynamics Converter # PD4135K

Continue Researching