HappiJac Swing Out Extension Brackets

Question

Question:

Ive seen this product listed as #182496 on other websites. Is your product the same? Also, does this come as a set or do I need to buy 2? Thanks!

asked by: Jill R

0

Expert Reply:

The part 182496 is listed on our site as part # LC182496. It is the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems, and it does in fact come in a set of two. I've linked to a video review of these extension brackets for you.

expert reply by: Kef G

0

Answer 1

I contacted the Rep at Happijac to inquire on your question of the HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks, #HJ54FR. His response was that yes, you can "stack" the extensions. There is however a point…

view full answer...

Answer 2

The Swing Out Extension Brackets #LC182496 can be left in the out position and not swung in. Since your 2010 Ram 4500 has a flat bed the part I think you are looking for is the HappiJac Extender Bracket #HJ54FR. This is a fixed extender that does not…

view full answer...

Answer 3

Hi David, The HappiJac Extender Bracket for Dual Wheel Chassis Truck Camper Jacks #HJ54FR is designed to hold more weight than the jacks that it works with so it's only rated up to the jack's capacity by the manufacturer. It's actual…

view full answer...

Answer 4

As long as it is properly installed the HappiJac Extender Bracket #HJ54FR won't cause you any issues. Will it add some stress? Of course it will since you're extending the jacks out. However, it won't be enough to result in a problem and…

view full answer...

Answer 5

The length of the HappiJack Swing-Out Extender Bracket #HJ54FR is 16 inches, the width is 5 inches, and the distance between the mounting holes is 7-1/2 inches. I went ahead and attached a diagram of the dimensions to this question as well as a video…

view full answer...

Answer 6

Hey Jonathan, it's odd but the Happijac Extender Bracket part #HJ54FR does not come with mounting hardware. You'd basically need to take the current hardware from your setup to a hardware store so you can get a duplicate bolt and nut so that…

view full answer...

Answer 7

I recommend using the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems item #LC182496 and the HappiJac Fixed Extender Bracket for Dual Wheel Chassis Truck Camper Jacks item #HJ54FR. The fixed extenders are only 5" wide apiece.…

view full answer...

Answer 8

Yes the HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks Item #HJ54FR that you referenced is the same design as what your 2019 Northern Lite 10-2 EXCD LE has.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

HappiJac Swing Out Extension Brackets

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching