Handle Attachment on the Deadbolt Lock with Inside Safety Release

Question

Question:

I was wondering what type of handles would work with this latch system. It looks like it doesnt come with a handle, but from the pictures I cant see where one would attach. Are there any paddle style handles that would work with this? Thanks!

asked by: Breana

0

Expert Reply:

The Deadbolt Lock with Inside Safety Release part # PLR7011S does not have a handle attachment point. In most cases a handle is attached to the actual door and is used to open and close it while this is to keep it secure.

expert reply by: Randy B

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

For a 2013 Honda CR-V we have the Blue Ox Base Plate Kit - Removable Arms #BX2258 that will work well with your Blue Ox Tow Bar. I recommend using Loctite Threadlocker #LT37420 for this installation. For your vehicle wiring, I recommend the Hopkins…

view full answer...

Answer 7

Hey Kirk, The Deadbolt Latch with Inside Safety Release for Enclosed Trailers #PLR7011S doesn't have a slot for a handle to attach to it. This is just a separate deadbolt that would only be able to be used if you were inside the trailer.

view full answer...

Answer 8

Hello Javier, As I would love to make your life easier and tell you it is not necessary, I cannot do so. Brake Burnishing (bedding-in, or break-in) should be done for the following reasons: - Achieve Maximum Performance: Burnishing evenly transfers a…

view full answer...

Answer 9

It sounds like there's an issue with the wiring on the right hand side of your trailer. The Dexter Nev-R-Adjust Electric Trailer Brake Kit item #23-468-469 should be equal adjusted at this point. I recommend checking all the wires and especially…

view full answer...

Answer 10

The Torflex Lift Kit - Tandem Axle - 2-7/8" Lift #K71-724-02 is designed for #11 Torflex axles so it will work with yours that has a 3,500 lb weight capacity. The capacities are more of a guide because generally that number axle has a higher…

view full answer...

Answer 11

It looks like the closest we have to those measurements is the Replacement Support Arm Assembly for Solera Pitched RV Awnings LC260294 which measures 66 1/8" long. Just to be clear, you will need to measure the wall mount from the top to the…

view full answer...

Answer 12

You are correct. You will want to use the backing plate to sandwich the boards and provide the most secure connection when installing the Brophy Swiveling D-Ring Anchors #RR6K-4 . You can mount these in a recessed hole created by a router or punch…

view full answer...

Handle Attachment on the Deadbolt Lock with Inside Safety Release

Product Page this Question was Asked From

Continue Researching