Dimensions of the Pipe Mount for the Bulldog Trailer Jack with 5,000 lb Capacity

Question

Question:

Male mount that is welded on the swivel Jack. What are the demensions? ID= OD= Thanks

asked by: Steven K

0

Expert Reply:

I went out into our warehouse and measured the inner and outer diameter of the mounting bracket that is on the Bulldog Round, Pipe-Mount Swivel Jack # BD178101 and found that the outer diameter measures 2 inches and the inner diameter measures 1-1/2 inches.

expert reply by: Jameson C

0

Answer 1

I visited our warehouse and took measurements of both of these jack mounts to confirm their compatibility. Yes, both the 2000-lb-rated Bulldog Jack #BD158109 and the 5000-lb-rated Pro Series Jack #PS1401420303 use the same round 2-inch weld-on pipe…

view full answer...

Answer 2

We ran out to the warehouse and took some measurements, and the pin on the Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate #PS1401420303 is 1/2" in diameter, and the pin hole is 5/8" in diameter. I linked a short review video of the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Dimensions of the Pipe Mount for the Bulldog Trailer Jack with 5,000 lb Capacity

Continue Researching