Can Curt Chain Hangers Be Used Instead Of Clamp On Hangers Provided With BXW2000?

Question

Question:

Hi, I do not have room for the clamp on on my dump trailer. Problem is that there is a hydraulic box that would be on the way for the clamp on. I have room 8 inches back to be able to install the bracket. Would this work or do I need to buy a different unit all together? Can Item # C17005 be used instead of the clamp on provided with BXW2000?

asked by: Nab

0

Expert Reply:

The Chain Hangers for Curt Weight Distribution Systems - Bolt On # C17005 will work for chain style systems that don't have sway control, so if you replace the tightening clamps of the Blue Ox SwayPro Weight Distribution w/ Sway Control # BXW2000 you would lose the sway control ability of the hitch but it could still function for weight distribution.

My recommendation instead is to use the Blue Ox Signature Series Lift Brackets for SwayPro Weight Distribution Systems - Clamp On or Bolt On # BXW4021 and bolt them to your frame so you keep the complete function of your weight distribution system with integrated sway control.

If you don't have the ability to bolt these on in the correct location, then an alternative system is recommended.

expert reply by: Jason S

0

Answer 1

There's a surprisingly easy way you can determine exactly what spring bars you have and therefore exactly what their tongue weight rating is. The bars are going to have dimples on them (see accompanying photo) which is going to tell you the bars…

view full answer...

Answer 2

Springs bars from Blue Ox that have two dots (sometimes called dimples or notches) are rated for up to 750 lbs of tongue weight. What you have are the Spring Bars for Blue Ox SwayPro Weight Distribution System #BXW4006.

view full answer...

Answer 3

The DeeZee #DZ91716 is constructed of .056 aluminum tread plate. Due to the fact that the box isn't very large, the box is pretty rigid but I wouldn't recommend standing on it. We offer another similar box from RC Industries, part #350970…

view full answer...

Answer 4

The overall dimensions of the Blue Ox Signature Series Lift Brackets #BXW4021 are 12" wide x 7-3/4" tall as you can see in the attached photo.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Hey Heath, thanks for reaching out! The Curt A20 #C55DR and the B&W Companion #BWRVK3670 you're looking at are both excellent 5th wheel hitches, but I have to go with the Companion in this case simple because it is more robust and has a…

view full answer...

Answer 9

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 10

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 11

The Head Unit and R16 Roller Adapter #C16515 is more of an entry level fifth wheel head designed for a lower price point, whereas the A16 part #C16520 is a bit nicer with it's 2 piece jaw system that will provide better king pin contact which…

view full answer...

Answer 12

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Can Curt Chain Hangers Be Used Instead Of Clamp On Hangers Provided With BXW2000?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching