Clearances for Curt and Draw-Tite 2 Hitch Receivers on a 2019 Toyota RAV4

Question

Question:

Between the Curt and draw tite, whick leaves better clearance and what is the difference?

asked by: Deb R

0

Expert Reply:

When we installed the Curt Trailer Hitch # C13416 on a 2019 Toyota RAV4 we found that it measured 5" from the center of the hitch pin hole to the rear edge of the bumper, and then from the ground to the top inside of the receiver measured 12".

When we installed the Draw-Tite Trailer Hitch # DT82QR on a '19 RAV4 we found that these dimensions were the same so the clearances will be the same either way.

Out of both options I recommend the Curt trailer hitch over the Draw-Tite simply because we have found that the Curt hitches tend to have better welds and a thicker powder coat which will help it to wear better over time.

Attached are installation videos for both that you can check out. If you let me know what you plan on using it for I can make additional recommendations as necessary.

expert reply by: Jon G

0

Answer 1

I was able to speak to a representative from EcoHitch today. I was told that the EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2", part #306-X7219, measures from 10-1/4" from the ground to the top of the hitch receiver.

view full answer...

Answer 2

Good question, and the panel you are referring to does get reinstalled on your 2018 Toyota RAV4 when installing the etrailer Trailer Hitch Receiver #e98864. You will trim a small section of it (as shown in the cut out below), and the same push pins…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

Curt requires the use of their stabilizer strap part #18050 when using some of their lower capacity hitches to carry a non-supported load like a bike rack. I attached a review video for you to check for the strap as well. Because of that I would…

view full answer...

Answer 5

Yes, the bolts of the etrailer Trailer Hitch Receiver #e98864 are M12-1.25 x 35mm bolts. So for a thread tap you will just need a 12 mm x 1.25 tap.

view full answer...

Answer 6

The Curt hitch part #C13406 and EcoHitch part #306-X7219 are both a confirmed fit for your 2018 Toyota RAV4 and will provide a trailer hitch that has a concealed crosstube making it less visible than most hitches overall. The key differences are that…

view full answer...

Answer 7

The 2018 Toyota RAV4 with the factory tow package comes with the factory 7-way trailer connection, a hitch receiver and a small oil cooler. Having those components is a nice option, but it was a lie that any other system would cause a check engine…

view full answer...

Answer 8

Trailer hitches do not have threaded hitch pin holes. The threaded bolt for your Thule bike rack will thread into a weld nut (or other retention device) that is in the bike rack's shank and pull it tight to the side of the hitch receiver. This is…

view full answer...

Answer 9

If you don't like the etrailer Trailer Hitch Receiver part #e98864 because of the visible crosstube then check out the EcoHitch Hidden Trailer Hitch Receiver part #306-X7219 which has a concealed crosstube that provides a much cleaner look and…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Clearances for Curt and Draw-Tite 2 Hitch Receivers on a 2019 Toyota RAV4

Featured Help Information

Miscellaneous Media

Continue Researching