Installation of DeeZee Trailer Tongue Tool Box # DZ91716

Question

Question:

Im putting the box on a aluminum boat trailer. How does it install? Is there pre drilled holes and only holes need to be drilled into trailer? Are U bolts needed?

asked by: Angelo

0

Expert Reply:

The DeeZee Trailer Tongue Tool Box does not feature pre drilled holes, but the included sheet metal screws can be used to secure the box to the trailer tongue. The instructions call for 3/16 inch holes to be drilled through the bottom of the box into the trailer frame. Make sure you avoid any wires that might be running along the trailer frame. You can see the installation instructions by clicking the provided link. You could use u-bolts if you wish.

expert reply by: Mike L

0

Answer 1

In regards to the Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery part #3802308, the red wire from the breakaway battery box goes to the battery charge line circuit also known as the twelve volt power supply on the…

view full answer...

Answer 2

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Answer 3

The DeeZee Specialty Series Trailer Tongue Toolbox #DZ91716 may be what you're looking for. It measures 34 inches long in the back, 16 inches long in front, 14-1/4 inches wide and 18 inches tall. It's a 3.71 cubic foot box that locks and…

view full answer...

Answer 4

Yes, you can connect your Breakaway Switch #FA80-00-2060 to a larger battery than a standard 5Ah #3801250 or 10Ah #BRW87FR breakaway batteries. This is the way most campers operate since they are going to have a larger battery to operate lights on…

view full answer...

Answer 5

The DeeZee Specialty Series Trailer Tongue Toolbox #DZ91716 that you referenced weighs 26 lbs. The overall dimensions are 34" long (back) x 16" long (front) x 14-1/4" wide x 18" tall.

view full answer...

Answer 6

The Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 is the correct replacement grease cap for your Dexter 85-1 plug; both are plugs for 1.18" hole. I've left a link to a video review of this product for you to take a look at.

view full answer...

Answer 7

The Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 will replace your missing rubber cap on your Dexter E-Z lube axle hub.

view full answer...

Answer 8

The most corrosion resistant jack for your application is the Bulldog Round A-Frame Jack, #BD1550101344, that you mentioned. This jack has a clear zinc finish and will last much longer in the salt water environment you described. Stepping up to a…

view full answer...

Answer 9

We offer rubber grease cap plugs like #DC-RP which fits a 1.18-inch dust cap hole; this is sold as a single piece. We also offer a set of two in the same size as part #RG04-010. These fit grease caps like #RG04-040.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Installation of DeeZee Trailer Tongue Tool Box # DZ91716

Product Page this Question was Asked From

Continue Researching