Dexter 8-247-Hub Bearing Buddy and Bearing Kit Fit

Question

Question:

IS Item # BB1980A-SS correct for my Dexter 8-247-Hub? Is Item # BK2-100 correct for my Dexter 8-247-Hub? Notice 8-247 not 8-248

asked by: David B

0

Expert Reply:

Yes the Bearing Buddy part # BB1980A-SS is correct for the Dexter hub you have # 8-247-50UC3 and then for the bearing kit part # BK2-100 is also correct! You made my job easy.

expert reply by: Jameson C

0

Answer 1

Hey Dan, welcome back. The only bolt kit we have for your DeeMaxx Disc Brake Kit item #DE62FR, is the Mounting Bolts and Hardware for 10" Brake Assemblies item #BRKH10A. These have a zinc coating to protect them. We do not have a stainless steel…

view full answer...

Answer 2

Sounds like you are looking for a mounting bolt kit for your trailer brakes. For that we have the Mounting Bolts and Hardware for 10" Brake Assemblies #BRKH10A. This is for assemblies that attach with 4 bolts. If instead you have 5 bolts…

view full answer...

Answer 3

Galvanized metal parts are definitely better if your application is salt water use. We do offer a galvanized hub/drum assembly in the 3500-lb axle rating and with the 5-on-4-1/2 bolt pattern you need. Hub/drum kit #8-247-50UC3 includes the bearings…

view full answer...

Answer 4

According to B&W the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1020 is about a 2 hour install by a professional. All the Hardware is provided. I have attached the installation instructions so you…

view full answer...

Answer 5

The trailer brake controller wires on a 2018 Ford E-450 are blue for brake output, yellow/red or gray/red for 12 volt power, violet/white or yellow/green for stop light, and black/gray or black/violet for ground. These wires will all be located…

view full answer...

Answer 6

I believe I was able to find the bearings and seals that you need, but you'll want to double check on your end by removing the hub and looking at part numbers just to make sure. Inner Bearing - #25580 Inner Race - #25520 Outer Bearing - #02475…

view full answer...

Answer 7

You can add a heavier axle to the trailer but the rest of the components of your trailer may not be rated for a higher weight capacity such as the suspension components and wheels. If you go from a 3,500 lb axle to a 7,000 lb axle like part #8327834…

view full answer...

Answer 8

All of our bearing kits, like the part #BK2-100 that was referenced, only include the inner/outer bearings, grease seal, and cotter pin/washer but I can help you get the other parts that you are needing as well. For 10" x 2-1/4" brakes we…

view full answer...

Answer 9

EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…

view full answer...

Answer 10

Yes you can use a Bearing Buddy on your current axle setup but you'll have to remove the zerk/grease fitting. What you have now is an EZ lube spindle which allows you to push grease through the middle of the spindle but you can install a Bearing…

view full answer...

Answer 11

I reached out to my contact at Dexter and was able to get the wheel bearing numbers you need for your 1999 Jayco Pop-Up Camper. The inner bearing is #L68149 and the outer bearing is #L44649. I recommend getting the complete kit which is Bearing Kit…

view full answer...

Answer 12

When using an EZ-Lube hub, such as hub/drum assembly #AKHD-545-2-EZ-2K, on an EZ-Lube spindle it is not necessary to also use Bearing Buddy bearing protectors. An EZ-Lube spindle, such as part #TRU44FR, has a grease zerk fitting to allow you to pump…

view full answer...

Dexter 8-247-Hub Bearing Buddy and Bearing Kit Fit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching