Replacement Tail Lights for 2014 Rockwood Aliner

Question

Question:

I broke the red passenger tail light on a 2014 Rockwood Aliner. The number of the light says SAE-AS2T2I6. which is the light to replace this?

asked by: Yvonne O

0

Expert Reply:

It looks like the 2014 Rockwood Aliner uses the RV Tail Light part # RVSTB60 for passenger side or part # RVSTB61 for driver side.

expert reply by: Conner L

0

Answer 1

You will want the Wesbar 8-Function LED Wrap-Around Tail light #271595 for the left hand side of your trailer, and for the right side you will want the Wesbar 7-Function LED Wrap-Around Tail Light #271594. These lights are LED and have a very similar…

view full answer...

Answer 2

To upgrade your lights, an exact replacement won't really be possibly but retrofitting an upgraded LED option will be super easy. For this, I recommend the Dual LED Trailer Tail Light - Stop, Turn, Tail, Backup - Red and Clear Lens#CE86FR by…

view full answer...

Answer 3

Hello David, thanks for reaching out. The matching passenger side light to the Optronics #OPT34KB is the following: - Optronics LED RV Tail Light - Stop, Tail, Turn, Backup - Oblong - Passenger Side #OPT54KB

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Tail Lights for 2014 Rockwood Aliner

Continue Researching