Does Curt Brake Controller Adapter for 2010 Ram 1500 Fit a 2018 Ram 1500

Question

Question:

Will the 51438 controller wire adapter work on a 2018 Dodge Ram 1500. I have a Curt Venturer controller. I was using it on a 2010 Dodge Ram, and now would like to move it over to a 2018. Thanks

asked by: Stephen B

0

Expert Reply:

The adapter that fits the 2018 Ram 1500 is part # C51458.

The # C51438 that you used in your 2010 Ram only fits through 2012

expert reply by: Charles S

0

Answer 1

For a 2010 Dodge Ram 1500 with a 7-way there is a port under the dash that will be used for the install of a brake controller. The install harness part #3021-P is the harness to use. The plug you are looking for is a white, square connector above the…

view full answer...

Answer 2

Since your 2010 Ram 1500 has a round 7-way connector at the rear of it that means a brake controller like our best selling Prodigy P3 part #90195 could easily install with the correct harness, part #3021-P. The harness is located underneath the dash,…

view full answer...

Answer 3

We do have a solution for a plug-in trailer brake controller for your 2010 Dodge Ram 1500. You mentioned accepting both plugs though, and an aftermarket brake controller will plug into just one of them, and connect to the brake controller. If you…

view full answer...

Answer 4

With one exception, you will need to see your local Ram dealer to reconfigure the TIPM (Totally Integrated Power Module) on your 2012 Ram 1500 to install an aftermarket brake controller. The exception is the Curt Echo Mobile Trailer Brake Controller…

view full answer...

Answer 5

Dodge switched their brake adapter pin configuration on the Ram 1500 for the 2010 model year. If your 2010 Dodge Ram 1500 has the factory 7-Way connector you will just need the Tekonsha Brake Control Adapter, part #3021-P. This will plug into the…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I have an adapter that will work with a 2013 Ram 1500, but unfortunately Ram switched things up between 2010 and 2013 and the brake controller harnesses are different. Part #3021-P fits the 2010 models and 2013 requires #3023-P. I've attached an…

view full answer...

Answer 8

The excellent Tekonsha Prodigy P3 Brake Controller #90195 is intended for mounting with its included bracket as shown in the linked installation video. This unit's size and shape will prevent it from fitting properly in the small recess in your…

view full answer...

Answer 9

The brake controller installation on a 2010 Dodge Ram would be pretty much identical to that as the 2009 model shown in the video. The installation port is located under the dash midway between the emergency brake and the brake pedal, just above…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Does Curt Brake Controller Adapter for 2010 Ram 1500 Fit a 2018 Ram 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching