Will Curt RockerBall Interfere with Surge Brakes

Question

Question:

Wondering if the Curt Rockerball will interfere with my surge brakes, Thaks

asked by: Bruce P

0

Expert Reply:

The Curt Rockerballs like the # C43KR will not interfere with your surge brakes. The movement they allow would not prevent the inertia of your vehicle applying the brakes from activating your surge actuator.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Thanks for letting us help Ben. For a setup like yours, I'd recommend loading the UTV and connecting the trailer with the Pacbrake airbags at their minimum required pressure. From there, you'll want to adjust the B&W Continuum weight…

view full answer...

Answer 6

Hi Ryan; the Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS56ZR is designed in the US but manufactured in China. The Weigh Safe ball mounts with the built-in scale are pretty unique so we don't have a USA made option with the same…

view full answer...

Answer 7

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 8

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 9

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 10

Hey Larry, Yes, a high-low adapter may be needed to keep the tow bar level between your Class A motorhome and your 2026 Ford Maverick. With the Roadmaster #RM87NQ base plate and 225/55R19 tires on the Maverick, the tow bar attachment height is about…

view full answer...

Answer 11

Hi John! The BulletProof Aluminum Hitch w/ Stainless Steel Dual Ball for 2" Hitch - 4" Drop/Rise - 14K #BPH32YR is anodized, so it isn't just raw aluminum. That actually goes for all of BulletProof's aluminum ball mounts, which is…

view full answer...

Answer 12

Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…

view full answer...

Will Curt RockerBall Interfere with Surge Brakes

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching