Replacement Mounting Hardware for Thule Hyper XL Cargo Box

Question

Question:

Hello, I recently picked up a used Porsche Thule Hyper XL cargo box and it doesn’t have the correct mounting hardware for my 3.5” Whispbar cross bars. What mounting parts do I need and do you carry them?

asked by: Harold

0

Expert Reply:

The mounting hardware for the Thule Hyper XL TH612 is the part # TH7521484001 which is designed to fit bar dimensions of up to 3-1/2" wide x 1-11/16" tall. If you have bars that are taller than 1-11/16 inches there won't be a way to make the box fit better with modifications.

expert reply by: Jameson C

0

Answer 1

You can't just replace the rubber pieces you will need to replace the entire clamp. Which clamp you need depends on which Thule box you have. If your box is the Thule Pulse Alpine (613), Pulse Medium (614), or Pulse Large (615) you will want the…

view full answer...

Answer 2

Thank you for the picture! So right off I can say that you will need to get more than 1 of the Replacement Cradle #TH8523387001. Since it's a different design than the other 3 I recommend picking up 2 of these and using them for the Quick Grip…

view full answer...

Answer 3

We do have replacement mounting hardware for your older Thule Atlantis 1800 687 cargo box! The Quick Grip is part #TH05738, and then we also have the Slide Strip #TH05401 and the Replacement Cradle #TH8523387001 as well if you're needing those.

view full answer...

Answer 4

The flat side of the Replacement Cradle for Thule AcuTight and Quick Grip Mounting Hardware part #TH8523387001 will go against the bottom of the cargo box which you can see in the attached photo. Therefore, the screw hole will be facing down towards…

view full answer...

Answer 5

Yes, the AcuTight system is basically just an upgraded QuickGrip system so you could upgrade your Quickgrips out of your Atlantis 1800 to the Acutight system by installing the part #TH7521484001. Both systems use the same cradles part #TH8523387001.

view full answer...

Answer 6

I went ahead and brought the issue to my contact at Thule, and he said to either use WD-40 to spray on the available threading and use a pair of pliers to grab onto the T-Bolt while you try to rotate the knob. This will allow you to have extra…

view full answer...

Answer 7

Yes, Thule Replacement Lid Lifter Hinge #TH14936 is the correct part for your Hyper XL Rooftop Cargo Box. Thule provides excellent spare parts support for its customers; all Thule cargo box replacement parts are shown on the linked page.

view full answer...

Answer 8

Yes, there is. To add a set of flush mount crossbars to your 2023 Ford Expedition's raised side rails, I recommend the Rhino-Rack Vortex StealthBar Roof Rack item #JB0190. These crossbars mount directly to the side rails and have a flush design…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Mounting Hardware for Thule Hyper XL Cargo Box

Continue Researching