What Lengths Are the CE Smith Support Bracket for Tandem Axle Fenders Offered In

Question

Question:

Do you have a similar part that is longer than this part?

asked by: Greg C

0

Expert Reply:

The CE Smith Support Bracket for Tandem Axle Fenders is offered in two different lengths, part # CE26236 for 15" or part # CE26238 for 17-1/16".

expert reply by: Conner L

0

Answer 1

I spoke with CE Smith about the CE Smith Support Bracket for Tandem Axle Fenders part #CE26238 and they said the flat potion is 13.88", the angled ends are 2", and the entire bracket is 17.03" long. I have created a diagram for you…

view full answer...

Answer 2

For the Tandem Axle Teardrop Trailer Fenders for Boat Trailers - Steel - 14" Wheels #HP54VR, it really depends on how you install the fenders. If you bolt the fenders onto your boat trailer, they will definitely not be able to accommodate 300…

view full answer...

Answer 3

The Replacement Silicone Dust Boot w/ Metal Core for DeeMaxx Disc Brake Calipers #DE23FR is used to prevent the entrance of dirt and moisture which could cause corrosion and/or impair caliper operation. To replace it you're going to need to slide…

view full answer...

Answer 4

The caliper pins do not need lubrication on a trailer. I've attached a video and an article on installing disc brakes for you to take a look at. Although it wouldn't hurt anything if they are lubricated either.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Lengths Are the CE Smith Support Bracket for Tandem Axle Fenders Offered In

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching