Will the Draw-Tite Trailer Hitch Fit a 2020 Honda CR-V Hybrid

Question

Question:

Do you sell a hitch for a 2020 Honda CRV Hybrid all wheel drive. I am sure the hitch for the standard model does not work. Apparently the battery accommodation structure of the hybrid does make a difference in the fitment.

asked by: Mike Z

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76128 will not fit a 2020 Honda CR-V Hybrid per Draw-Tite because of the cross tube location. Instead, I recommend the etrailer Trailer Hitch Receiver part # e98848 which will fit Hybrid models.

expert reply by: Conner L

0

click to enlarge

Answer 1

It actually looks like the ladder you currently have is exactly what you're already looking for - you just need to remove the screws from those bottom supports and then you can flip the ladder up since it's hinged higher up. If that isn't…

view full answer...

Answer 2

From what I could find on your Valeigh Beacon 34RLB 5th wheel it is 13'1" tall (13.08). The Lippert On-The-Go Telescopic Ladder #LC64HD you were looking at is only 12-1/2' tall, so it would not be tall enough to reach the top of your 5th…

view full answer...

Answer 3

Hello Danny, Great question! I am sorry but the TowSmart Trailer Hitch Receiver - Custom Fit - Class III - 2" #TS67ZR does not fit the hybrid model. The good news is that our etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish -…

view full answer...

Answer 4

The Draw-Tite Class 3 Round Tube Trailer Hitch #76128 you're looking at is actually not intended for the Hybrid models, so I can't confirm if it'll work with the kick sensor, but I can say that we have had a customer use the etrailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Will the Draw-Tite Trailer Hitch Fit a 2020 Honda CR-V Hybrid

Products Featured in This Question

Continue Researching