Replacement Top Wind Handle for Atwood Mobile Products Trailer Jack

Question

Question:

I have Atwood Mobile Products boat trailer jack and broke the crank handle. Its made of 1/2inch material cant find a part number. The only number I found was on the gear cover 85701.

asked by: Edward B

1

Helpful Expert Reply:

We do have a top wind crank handle for your Atwood Mobile Products trailer jack. The part that will work for you as a replacement handle is:

- Top Wind Trailer Jack Handle # JP02-010

This will work for a variety of trailer jacks, including your Atwood.

expert reply by: Kyle S

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Matt, welcome back! You are correct. The threaded hole on the Weigh Safe 180 Hitch 2-Ball Mount for 3" Hitch item #WS34MR ball retainer, is to make removing the pin easier. You can insert a 1/4"-20 screw to get additional leverage to…

view full answer...

Answer 6

Hi Cory, can you tell me the specific part numbers and which measurements you want exactly? I only see that you looked at some Trimax HD ball mounts, and I want to make sure I'm getting all of the measurements you're looking for and on the…

view full answer...

Answer 7

Hi John! The BulletProof Aluminum Hitch w/ Stainless Steel Dual Ball for 2" Hitch - 4" Drop/Rise - 14K #BPH32YR is anodized, so it isn't just raw aluminum. That actually goes for all of BulletProof's aluminum ball mounts, which is…

view full answer...

Answer 8

Hello Brian, Thanks for finally finding an opportunity to write in. Yes, the B&W Continuum Weight Distribution System #BW78FR would be a great choice for your 2025 Ford Expedition Tremor with the HD towing package and your Rockwood Mini Lite…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 11

Hey Adam, the correct Kuat DEK Platform rack with light bar for your 2026 Toyota Tacoma would be the part #KU73SR. The correct Kuat Ibex Overland Truck Cap then too would be the part #KU99SR that you referenced. Now the top of this would be lower…

view full answer...

Answer 12

Hey Lee! The Victron parts can get pretty confusing. The Victron Orion-Tr #VN75ZR is only designed to be a power supply for DC loads, not for battery charging. You do not want to use this converter to charge any type of battery. To charge your…

view full answer...

Replacement Top Wind Handle for Atwood Mobile Products Trailer Jack

Product Page this Question was Asked From

Continue Researching