Dust Cap for 2.74" Hube bore

Question

Question:

I am looking forTrailer Hub Grease Capps below. I dont know if they will fit. I measured with a micrometer 2.74 ID on the axel. Do they make caps that size or did I just measure wrong

asked by: Kip K

0

Expert Reply:

I have two options that are very close to the 2.74" ID that you measured. They are 2.72" ID re check your hub and measure about 1/2" in to the hub face.

For non ez lube hubs use Zinc Plated Grease Cap - 2.72" Outer Diameter part # TRDC-275

For E-Z Lube use the Dust Cap part # K7CAP

expert reply by: Randy B

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 4

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 5

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 8

From what I can find the Norcold N306.3 fridge has a 2.7 cu ft capacity and is 20-1/8" wide and 26" tall. The most similar option we can offer is the 3.2 cu ft Everchill RV Mini Refrigerator #324-000111. The #324-000111 measures…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

Hey Gene, welcome back! The correct tie-downs are the TorkLift Talon item #TL45SV, you were looking at. This a set of front and rear tie-downs. The rear ones will attach directly to your 2025 Ford F-450's TorkLift SuperHitch Magnum hitch item…

view full answer...

Answer 11

Hi Chas, The Lippert Road Armor Shock Absorbing Equalizer part #LC53CK may work for your trailer, but that will depend on what equalizer is currently on your trailer. In order to determine what equalizers would be a fit for your trailer, we'll…

view full answer...

Answer 12

Hey Victor, yes the Long U-Bolt Kit part #RM33KT is a Roadmaster brand u-bolt kit. This does include nuts and washers as well.

view full answer...

Dust Cap for 2.74" Hube bore

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching