Could Trailer Jack # TJB-2001SB Fit Same 2.5 inch Pipe Mount as Bulldog Jack

Question

Question:

I am replacing a Bulldog swivel/snap ring jack that is frozen up and can no longer be raised or lower the swiveling is okay. The opening for the swivel is 2.5 inches in diameter. By chance, would the swivel of the referenced jack be 2.5 inches and allow me to install it into the existing already welded mount on the trailer? Thank you.

asked by: JIm J

1

Helpful Expert Reply:

The snap ring mount that the # TJB-2001S-B fits is the same 2-1/2 inch diameter as what your trailer has now so it will fit the same mount and work well.

expert reply by: Jameson C

1

Answer 1

The Fulton Snap-Ring Swivel Marine Jack with Fixed Length - 400 lbs #F1410050149 has a fixed height of 14-1/2 inches. We don't have a fixed height option for a 1,500 lb jack, so I recommend the Fulton Bolt-Thru Swivel Marine Jack - Bolt On…

view full answer...

Answer 2

In order to haul two kayaks in your 2016 Toyota Tacoma without placing them on the roof of your vehicle, you will need to use a load extender such as the Malone Axis Truck Bed and Roof Load Extender part #MPG907 if the bed of your truck is empty. The…

view full answer...

Answer 3

The Thule Vertex 2 Bike Rack TH9028XT is a nice bike rack. Unfortunately each manufacturer has a different threaded hitch pin to use as a lock and anti-rattle device for their bike racks and unfortunately they are not compatible with each other. Each…

view full answer...

Answer 4

You are absolutely correct that the two different tire sizes, 16.5x6.5-8 and 165/65-8, are in fact the same size, the latter being the modern metric designation. The part you referenced, Kenda #AM3H200, is a 165/65-8 bias-ply tire/wheel with a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Answer 8

Hey Eric, the closest tire size to the ST155/80R13 you have is the ST175/80-13. I did some calculations on the tire sizes and found that the difference between the 175/80R13 and the 155/80R13 is pretty small. The 175/80 is 24 inches inches tall…

view full answer...

Answer 9

Hey Jim, thanks for reaching out. The swivel mount that comes with the #e34RV jack uses M12 bolts. I grabbed one of the mounts from our warehouse to check, and it looks like it comes with M12 bolts, nuts and lock washers, so you shouldn't need to…

view full answer...

Answer 10

For your application we have the 2K Bulldog Round, Snap-Ring Swivel Marine Jack #BD151464 which fits with the L-Bend Bracket #F500242 that has the 2-1/2" opening you mentioned (see attached photo) and secures using the Snap Ring #BD500241.

view full answer...

Answer 11

We don't have a video of the #GL1 installed on a bi-fold trailer ramp but I did attach a picture we got from a customer who installed it on a bi-fold ramp setup for you to check out as well.

view full answer...

Answer 12

Hey Mike! Caliber Marine Slides #CA26AJ can handle the weight of your boat. However, for your 25' Pro-Line I recommend using the 3" wide Caliber Marine Slides #CA66AJ instead. With a 5,000 lb fiberglass boat, the wider slide is the better…

view full answer...

Could Trailer Jack # TJB-2001SB Fit Same 2.5 inch Pipe Mount as Bulldog Jack

Product Page this Question was Asked From

Continue Researching