Replacement 2-5/16" Inner Diameter Snap-Ring for Bulldog Trailer Jack

Question

Question:

Thickness of snap ring I need inside dia 2 5/16

asked by: Lloyd C

0

Expert Reply:

Since you have a Bulldog jack and you need the inside diameter of the retaining ring to be 2-5/16" then that means you need the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks # FP908600.

Attached is a review video that you can check out.

expert reply by: Jon G

0

click to enlarge

Lloydcrow

4/24/2020

Part should be here today

Chris R.

4/24/2020

Great! Just let us know if anything else comes up.

Lloydcrow

4/26/2020

Snap ring work fine thanks

Answer 1

You are correct, the Fulton Snap Ring, #FP908600, and Bulldog Snap Ring, #BD500241, are very similar. I went out to the warehouse and pulled both parts to measure them using digital calipers. Both had the following measurements: Inner diameter = 2.28…

view full answer...

Answer 2

The Replacement Swivel Snap Ring for Bulldog Jacks, #BD500241, fits Bulldog series 150, 160 and 170 snap-ring swivel jacks up to 5,000-lb capacity so yes, the same ring would be used for the 2,000 lb jack as well as the 5,000 lb jack. This ring has…

view full answer...

Answer 3

A snap ring like #FP908600 can be measured using a set of dial calipers or digital calipers to get the most accurate measurement possible. To measure the inside diameter, on the inside of the rind measure across at the widest point (not at the bottom…

view full answer...

Answer 4

The inside diameter of the Replacement Retaining Ring for Fulton Snap-Ring Jacks, part #FP908600 is 2.28 inches.

view full answer...

Answer 5

On the Pro Series Trailer Jack, #PSEJ10000101, the outside diameter of the snap ring is 2-1/2 inches, which is also the diameter of the circular opening that attaches the jack to the mount. The inside diameter of the snap ring is 2.28 inches. The…

view full answer...

Answer 6

In regards to the snap ring mount Ram or etrailer swivel jacks like the Round Snap Ring Swivel Jack w/ Footplate part #TJB-2001S-B, the Replacement Mounting Bracket for etrailer and Ram Snap Ring Swivel Jacks part #TJB-MB which comes with the jack is…

view full answer...

Answer 7

The Replacement Retaining Ring #SNP-RING measures 0.08 inches, but keep in mind there will be some slight variances on a per-ring basis. This is a replacement for specific jacks, which are the following Ram/etrailer jacks: TJB-2002-S, #TJB-2002S-B,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement 2-5/16" Inner Diameter Snap-Ring for Bulldog Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching