Bolt Thread Size of Mounting Hardware for etrailer Round Swivel Marine Jack w/ Wheel

Question

Question:

Hi, Whats the bolt thread size and length?

asked by: Victor

0

Expert Reply:

The bolts for the mounting hardware that comes with the Round Swivel Marine Jack w/ Wheel # MJ-1500B have an overall length of 4 1/4" and the thread is 3/8-16 course threaded.

If you are needing new hardware for this jack then we actually have that available as part # MJ-1000B-MBB.

expert reply by: Jon G

0

Answer 1

You can replace the mounting bracket and hardware on an #FXP10W0301 or #MJ-1200B, but the tube and swivel bracket are not available as replacement parts for these jacks. You can use the Replacement Mounting Kit for etrailer and Ram Swivel Marine…

view full answer...

Answer 2

Hey Hank, welcome back. You can email that picture directly to the email you receive this response from. I saw you previously purchased the Dutton-Lainson Boat Trailer Jack item #DL22210. What you're describing sounds like the Replacement…

view full answer...

Answer 3

Replacement Mounting Hardware for etrailer and Ram Swivel Marine Jacks - 1,200 lbs and 1,500 lbs Item #MJ-1000B-MBB will actually be perfect for you. I checked the specs on the actual jacks that come with this hardware and it is basically identical…

view full answer...

Answer 4

Thanks for the picture! I would be happy to help you. To mount your jack to your Bass Tracker 175 TWX trailer you will need the Mounting Hardware for Dutton-Lainson Bolt-On Trailer Jacks item #DL22443. This kit includes four 3/8"-16 bolts that…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Bolt Thread Size of Mounting Hardware for etrailer Round Swivel Marine Jack w/ Wheel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching