Safety Chain Solution that Fits Curt OEM Rail Kit Gooseneck Ball Kit C60692

Question

Question:

I have a CURT 60692 OEM Puck System Gooseneck Hitch, and the safety hooks on my stock trailer are to small to lock on the thick safety chain anchors. I was looking at the Andersen Ranch Hitch Safety Chains but are the hooks big enough to lock on my Curt safety chain anchors?

asked by: Derf R

0

Expert Reply:

Your best and easiest solution will be to replace the clevis hooks of your current safety chains with the part # C81970 which will easily fit the safety chain loops of the Curt ball and safety chain kit part # C60692 that you referenced.

expert reply by: Jameson C

0

Answer 1

To fit your Curt Ball and Safety Chain Loop Kit #C60618, you need hooks that can fit over the roughly 1" wide top and 3/4" sides. You could use the Curt Clevis Hook #C81980 which has a 1-1/4" opening. This hook has a lot more weight…

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hey Travis! The right MORryde GooseTech depends on the pin box bolt pattern and GVWR of the Solitude 310GK. If it is a little older it probably has a Lippert 1621, I believe the newer models use the Lippert Rhino. You can ask whoever you're…

view full answer...

Answer 6

Hey Tim, thanks for reaching out. The Shocker Hitch 5th Wheel to Gooseneck Adapter #SHK99YR may work for you, but fitment will depend on what pin box your camper was equipped with from the factory. Pin boxes aren't made and model specific to the…

view full answer...

Answer 7

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

Answer 8

Valerie, Jayco used both the Lippert Rhino and the 1621 across the North Point line depending on floorplan and production runs. I believe you likely have the 1621 pattern. The only way to know for sure is to check the sticker on the pin box itself.…

view full answer...

Answer 9

Hey Kevin! Yes, the B&W 5th Wheel to Gooseneck Pin Box #BW55RV will fit the 2026 Brinkley Model Z 2680. The Curt Helux only fits a Lippert Rhino bolt pattern so that makes it easy to identify. The B&W is designed for the Rhino as well so it…

view full answer...

Answer 10

Hi Jim! As long as your 2026 Alliance Valor 37V11 has the Lippert Rhino box currently, the B&W 5th Wheel to Gooseneck Pin Box - Lippert Rhino - 25K GTW - 3.25K TW #BW23RV will indeed fit. If you have a different pin box, just let me know and I…

view full answer...

Safety Chain Solution that Fits Curt OEM Rail Kit Gooseneck Ball Kit C60692

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching