Replacement Oil Seal Recommendation for Dexter 10,000 lb Trailer Axle

Question

Question:

Have a 22HD GN Big Tex trailer with 10,000foot Dexter axles and oil bath hubs and have leakey hub wondering what the seal part # may be

asked by: Kodi C

0

Expert Reply:

The correct oil seal for a Dexter 10k trailer axle is the part # 10-56 that you referenced.

expert reply by: Jameson C

0

Answer 1

Hey Darcy, In order to convert a Dexter 10K Axle (Made After May 2013) from electric drum to hydraulic disc brakes you'll need the following: Kodiak Disc Brake Kit part #K2R1058D11E (1 per Axle) Dexter Oil Hub for 9K to 10K General Duty Axles…

view full answer...

Answer 2

If you have oil leaking from the rear of the hub then that would indicate you either have the wrong size seal, you are over torquing the spindle nut, or you just have too much oil. I recommend you use the serial number on the axle that way you can…

view full answer...

Answer 3

Hey Johnny, thanks for reaching out. I am happy to look this up for you, but I will need the model number and serial number from your axle in order to get you accurate bearing/ seal info. Drop that info in the comments below and I am happy to send…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Oil Seal Recommendation for Dexter 10,000 lb Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching