Kit Needed to Install Fan-Tastic Vent Roof Vent

Question

Question:

Hello, I plan to install the roof vent FV802250 to Nissan NV2500 high roof. Do I need Butyl seal tape? what do I need for installation if the roof is - rubber? - metal? Thank you

asked by: Thang N

0

Expert Reply:

We have a kit made for installing roof vents, including the Fan-Tastic Vent Roof Vent # FV802250.

What you need is the Roof Vent Installation Kit # 344270KITW.

This kit does include butyl tape, which you'll need, as well as sealant and screws. This kit will work for you no matter if your roof is metal or rubber. I have added a link to a video review of this kit for you to check out.

expert reply by: Kyle S

0

Answer 1

Hey Robin! The Ceiling Garnish for Dometic FanTastic Roof Vent #FVK1060-81 is the correct replacement garnish for a FanTastic FV2200XWUSD81. I confirmed with the product manual that this is actually the exact same as the one that's originally…

view full answer...

Answer 2

The trim ring you are referencing is called a ceiling garnish. There are different colors and different depths with the ability to cut them to custom height. I've linked the page to your options to assist. All of them are 1-1/2 inches on each…

view full answer...

Answer 3

We have several replacement garnishes for the Fan-Tastic Vent Model 4000 in various colors and lengths: We have the Ceiling Garnish for Fan-Tastic Vents Roof Vent with 6" leg in White, #FVK1060-81. The garnish in black is, #MA10-20209.…

view full answer...

Answer 4

I attached a picture that shows the inside corners of the Ceiling Garnish #FVK1060-81 that you referenced to show you how round or square they are.

view full answer...

Answer 5

The Replacement Rubber Cap #37262105 is designed to fit over a brass city water inlet like the RV City Water Inlet #372321-B-36-A. The notch in the rubber cap will only allow for a limited amount of room to fit over the city water inlet. If you have…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Kit Needed to Install Fan-Tastic Vent Roof Vent

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching